Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: michiganbuck

Page 1 of 60 1 2 3 4

Search: Search took 0.06 seconds.

  1. Replies
    55
    Views
    2,387

    Gordon would know, He knows all about...

    Gordon would know, He knows all about threads....where is Gordon?

    Ops..OT:
  2. Replies
    55
    Views
    2,387

    Newbs might expect to take it on the chin once or...

    Newbs might expect to take it on the chin once or twice and not upset..could have saved the broken and brazed it back to ok...or not.

    but once the argument starts the the thread is busted.
  3. Replies
    7
    Views
    415

    Vise jaws need be set true to the jaw pocket...

    Vise jaws need be set true to the jaw pocket bottom. If the vise is threaded the bolt holes can be some oversized so the jaw may be knocked down tight.
    If the thread is in the jaw then the vise...
  4. Replies
    7
    Views
    542

    The cutting flute edge is often an an odd helix...

    The cutting flute edge is often an an odd helix or angle due to the way it is cut-in and the included angle needed to go from the tooth edge and where it is cut into.
    Best solution is to spin or...
  5. Replies
    24
    Views
    1,344

    It seems that some modern thinking is that if the...

    It seems that some modern thinking is that if the part does not fit the catalog cutter/tool then the part has to be redesigned. That thinking would be very limiting to manufacturing and...
  6. Replies
    7
    Views
    415

    Cut a piece of bar stock, drill a couple of...

    Cut a piece of bar stock, drill a couple of holes.. put it in a vise and tap the holes...
    Oh wait, cant do that, the vise don't work because of missing jaws.............darn.
  7. Replies
    100
    Views
    4,804

    Tesla home back-up battery was...

    Tesla home back-up battery was advertised/suggested for perhaps 4 days with limiting use. Not really much good for that high price when a simple gas portable costs only a few hundred.
  8. Replies
    7
    Views
    415

    You might draw a sketch and have a PM guy make...

    You might draw a sketch and have a PM guy make you a set.
  9. Replies
    100
    Views
    4,804

    I thought the Tesla home battery back-up a good...

    I thought the Tesla home battery back-up a good idea but it seems failing...

    The 10-kilowatt-hour option was marketed as a backup power supply capable of 500 cycles, at a price to installers of...
  10. Replies
    24
    Views
    1,344

    OT:[ but I would ask you to provide any that make...

    OT:[ but I would ask you to provide any that make any sense, or are worth the tooling to do it.

    Perhaps some device that needs a long dog-point screw, or a standard length one to hold/locate at 2”...
  11. Very often you swing your tool holder and sight...

    Very often you swing your tool holder and sight to a protractor if a certain angle is called.
    for one ups and the like HSS is good/OK. Inserts may be OK to good if having a long run and want to just...
  12. Replies
    13
    Views
    827

    I like to draw the work benches, workers and draw...

    I like to draw the work benches, workers and draw in the work flow...and on one sketch draw in Lighting.
  13. Replies
    6
    Views
    456

    How about the 2x4 stack holding up the motor..

    How about the 2x4 stack holding up the motor..
  14. Replies
    24
    Views
    1,344

    Oh the good old days when such a tap would be...

    Oh the good old days when such a tap would be fudged up by a tool maker or a grinder hand with not even a thought it was out of ordinary...and not need buy a special tap that might cost $30...
  15. I think we should ban all G words..they might be...

    I think we should ban all G words..they might be dangerous and make kids think about guns.
    U and N also because they are related to that bad word...and rhyming words like fun, run and sun.....nip it...
  16. Seems the size and rough needs and tolerances...

    Seems the size and rough needs and tolerances could make some sense of it, with not disclosing all the details...
    turn about 12 x 3", bore 1" hole to +- .xxx, Cut a thread. Turn, harden and and...
  17. Air is much safer under ground than electric as...

    Air is much safer under ground than electric as sparks cant be avoided.
  18. TV shows and people who never held a gun and rare...

    TV shows and people who never held a gun and rare to use a pocket knife are making the rules... Go figure ..not much we can do if out numbered..

    Get kids into...
  19. Replies
    17
    Views
    1,104

    Guess that is why Kenny Jarrett rifles cost so...

    Guess that is why Kenny Jarrett rifles cost so much.
    .164 to .209 .. that is a lot of error.
    QT: [ a used Savage 12 chambered in 260 Remington.] who knows who did the job..perhaps made his own...
  20. No wonder you have no fish..Don't worry what...

    No wonder you have no fish..Don't worry what machine a guy has but to post a sketch of the parts needed might get better answers.
  21. Replies
    162
    Views
    13,935

    Guess to add a good thing might be better than...

    Guess to add a good thing might be better than take something away. Agree sitting between parts is not good when running a one minuet part with need to open a door and all..
    I think a absentee and...
  22. I think I have ground Inconel but cant remember a...

    I think I have ground Inconel but cant remember a darn thing about it or what wheel was best. Seems like it ground like stellite, with black sparks, but that was a log time ago... I see around the...
  23. little chance of finding the one you need ..then...

    little chance of finding the one you need ..then it wont be right on..

    You cam make a tail base true to your bed and with that fitting a tail from ebay you should be up and running in short...
  24. Replies
    9
    Views
    439

    Layer and screw or/and glue abut 3" thick of...

    Layer and screw or/and glue abut 3" thick of hardwood boards and that will be likely just a tough/strong and cast iron. Having a friend with a metal lathe you might make a tube bushing with a set...
  25. Replies
    6
    Views
    627

    Also from LMGTFY YouTube...

    Also from LMGTFY YouTube
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4