Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: LockNut

Page 1 of 38 1 2 3 4

Search: Search took 0.01 seconds.

  1. Just so everyone knows, on all Fanuc Oi-F and all...

    Just so everyone knows, on all Fanuc Oi-F and all 30 series controls, you are given the option of 4 digit program #'s or 8 digit program #'s. Parameter #11304 bit 3 will let you change this. There is...
  2. Replies
    12
    Views
    1,025

    So, I see the forum police man has reared his...

    So, I see the forum police man has reared his ugly head again. Everybody has an ulterior motive to you Doug? I do perform searches on Doosan but "Doosan" isn't always in the title or body of the...
  3. Replies
    12
    Views
    1,025

    Thanks for the input everyone. I'm on the fence...

    Thanks for the input everyone. I'm on the fence on this also but I do think we who support Doosan miss a lot of posts because they do get buried somewhat, especially when the post are about Doosan...
  4. Replies
    12
    Views
    1,025

    Doosan only forum

    Hello Don and the rest of the forum, I was wondering if maybe the time has come to give Doosan it's own forum. What is everyone's thoughts on this, please?

    I am asking as an applications...
  5. Replies
    9
    Views
    803

    The DNM5700S has options that are standard from...

    The DNM5700S has options that are standard from the factory for mold work and high speed machining. 400 block look ahead, nano smoothing, jerk control, AICC 2 and of course the 15K spindle instead of...
  6. Replies
    109
    Views
    6,310

    My first job as a machinist was at U.S. Steel,...

    My first job as a machinist was at U.S. Steel, Gary South Works, 1979. There an old gentleman that didn't speak much to anyone so no one liked him. I got to talking to him when I noticed every day at...
  7. Replies
    20
    Views
    2,833

    Heidenhain and Seimens are very good at the...

    Heidenhain and Seimens are very good at the volumetric checking but the thermal comp is only as good as the machine tool builder is at implementing it. Heidenhain kinematics check is very robust and...
  8. Replies
    3
    Views
    562

    It might have something to do with minimum arc...

    It might have something to do with minimum arc length. Not radius but length. If the end point is so close to the start point, it may cause the control to think of it as a full circle. This happens a...
  9. Replies
    20
    Views
    2,833

    What I see a lot of shops do is to do a...

    What I see a lot of shops do is to do a kinematics check periodically throughout the day or after certain operations like roughing. As the machine warms up, yes, the kinematics are no longer totally...
  10. Replies
    20
    Views
    2,833

    First, TWP is turned off before TCP is turned on....

    First, TWP is turned off before TCP is turned on. Totally legal and this is my preferred way of starting a 5 axis toolpath. TWP before TCP is considered a safety move. It gets the tool safely out...
  11. Replies
    2
    Views
    273

    M198 from a card requires this: M198 P1234 where...

    M198 from a card requires this: M198 P1234 where P1234 is O1234 on the card. No extensions, just the 4 digit program number.

    The below should work also but I have had spotty success with this. The...
  12. Thread: Doosan

    by LockNut
    Replies
    36
    Views
    4,758

    "After seeing Samsung go under when they were a...

    "After seeing Samsung go under when they were a large machine builder for Mori and a lot of other brands including there own , Then Daewoo also was a large South Korean machine builder that went...
  13. Chicago, of all places. 1974, ROTC in high...

    Chicago, of all places. 1974, ROTC in high school. Full firearms training and marksmanship training. In the basement of the school itself. No one got shot. Who today would think that could happen?...
  14. My thoughts? Why are teachers not armed? Why do...

    My thoughts? Why are teachers not armed? Why do the security personnel chicken out and refuse to confront the perps? Why does it take, sometimes, so long for the police to show up? I am of the school...
  15. Replies
    86
    Views
    5,413

    The 0-6- time is not for the stock model but for...

    The 0-6- time is not for the stock model but for the future high/higher performance model. Not that it makes that much difference. Below is quoted from the article I read on the new corvette.
    ...
  16. Replies
    8
    Views
    896

    You set the Z to zero for each tool station by...

    You set the Z to zero for each tool station by using the tool setter. Then you set the part Z to zero by using a tool, usually a turning tool, by calling it up with it's offset and touching off on...
  17. Replies
    8
    Views
    896

    I didn't misunderstand anything. You did not...

    I didn't misunderstand anything. You did not state your case in the first post or the second. The answer to your last question is to set your endmill or drill with the Q-setter and set a tool offset...
  18. I worked at Kimber for a short period of time....

    I worked at Kimber for a short period of time. Exactly what Gordon said. While I thought it would be/was cool, it got old really quick. As in mind numbingly quick. Millions of the same parts per year...
  19. Replies
    8
    Views
    896

    OK, first, indicate the face of an empty tool...

    OK, first, indicate the face of an empty tool spot. If it is off, then you have a turret alignment issue and the machine was probably bumped or crashed. We know these things happen. If the tool is...
  20. Replies
    8
    Views
    896

    I work for Doosan, I can try to help. First, I...

    I work for Doosan, I can try to help. First, I need the exact model number, serial number and date of build. After that, I can try to lo0ok up this info. Or, maybe quicker, you can call service at...
  21. Well, I needed some humor early on a Monday.

    Well, I needed some humor early on a Monday.
  22. Replies
    9
    Views
    1,071

    If you are talking about the complete length of...

    If you are talking about the complete length of the pin minus the head, I doubt if they are draw polished. Most likely electropolished during mass production. No need for length wise polishing as...
  23. Replies
    6
    Views
    1,072

    Ahhhh, I get it, dry humor.

    Ahhhh, I get it, dry humor.
  24. Replies
    76
    Views
    6,274

    There are couple of guys on here that are running...

    There are couple of guys on here that are running a Doosan DNM5700S. Maybe someone will chime in. I work for Doosan so I may sound a little biased if I speak highly of them. I have run CNC's for...
  25. Replies
    426
    Views
    24,223

    I work for Doosan Machine Tools as an...

    I work for Doosan Machine Tools as an applications engineer. Periodically, I am asked to give a short tour and/or explanation of our business. Not Doosan's business but "our" business. I explained to...
Results 1 to 25 of 926
Page 1 of 38 1 2 3 4