Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: seagiant

Search: Search took 0.00 seconds.

  1. Replies
    16
    Views
    1,088

    Hi, Just a shout out to John Evans for all...

    Hi,
    Just a shout out to John Evans for all the help!

    No, I have not fixed it, but know where the problem has to be, but I have a detent ball that will not come out of the shaft, so have to...
  2. Replies
    16
    Views
    1,088

    Hi, Ok, went back to the Schematic and I...

    Hi,
    Ok, went back to the Schematic and I see only a plunger and spring inside the "Block".

    I assume that is what you are freeing up when you pour in the lubricant and get most feeds back to...
  3. Replies
    16
    Views
    1,088

    Hi, Here is another thing, I saw no "Pin"...

    Hi,

    Here is another thing, I saw no "Pin" at the top of the block, just a hole?

    Could that be it, is something broken in the block?

    Just something I noticed and I even took a piece of...
  4. Replies
    16
    Views
    1,088

    Hi John, Thanks for all the help, I...

    Hi John,
    Thanks for all the help, I went in and removed the Overload Clutch Trip Lever #80...

    This allowed me to get to the hole at the top of the "Block",...

    It also allowed me to...
  5. Replies
    16
    Views
    1,088

    Hi, Thanks, I've done that already... I...

    Hi,
    Thanks, I've done that already...

    I have been all over the Internet looking for clues on this.

    Part # 97 is the trip plunger and is spring loaded, it is in the bottom of the "block"...
  6. Replies
    16
    Views
    1,088

    Hi, Thanks, I just took all that apart and...

    Hi,
    Thanks, I just took all that apart and cleaned it as stated above.

    It was grungy but cleaning did not make any difference.

    Played with the set screw up and down and makes no...
  7. Replies
    16
    Views
    1,088

    Hi, Thank you very much, I pulled the lever...

    Hi,
    Thank you very much, I pulled the lever at the bottom and #100 rod, cleaned everything up and still no go.

    That leaves the plunger and spring at the bottom of the block that's suppose to...
  8. Replies
    16
    Views
    1,088

    Hi, Well tried to take the handwheel clutch...

    Hi,
    Well tried to take the handwheel clutch collar #91 off but can not get the detent ball out!

    Have to get that off to get to the bottom of the "block" to check the parts in there?

    Well...
  9. Replies
    16
    Views
    1,088

    Hi, Finally found a schematic, I can put up...

    Hi,
    Finally found a schematic, I can put up so we can each see.

    On this print the parts in the bottom of #94 Cam Rod Sleeve. (what we called the block)...

    Is #96 and #97.

    Is there a...
  10. Replies
    16
    Views
    1,088

    Hi, Ok, on the Quill Housing parts schematic...

    Hi,
    Ok, on the Quill Housing parts schematic there is a spring loaded plunger in the bottom of the block...

    Parts # 120 and 121.

    That may be the problem, but will need to remove the block...
  11. Replies
    16
    Views
    1,088

    Hi, Thanks for the suggestion... I went...

    Hi,
    Thanks for the suggestion...

    I went and wet everything down and worked it and everything is free from what I can tell and moves as it should.

    Admittedly, I do not see the "pin" you...
  12. Replies
    16
    Views
    1,088

    1965 BP Series I Quill Downfeed Question!

    Hi,
    Looking to bore a hole and wanting to use the power downfeed for the last pass.

    The Quill downfeed works as long as you hold the lever back to feed, but...

    Will not "lock" and hold...
Results 1 to 12 of 12