Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: SLK001

Page 1 of 13 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    21
    Views
    1,156

    The red and the yellow wires will be wires that...

    The red and the yellow wires will be wires that are attached with screws, not rivets. Take a brush and use mineral spirits to slowly clean sections of the wire to try to identify the colors. Or,...
  2. Replies
    21
    Views
    1,156

    Really? It clearly says "TO REVERSE INTERCHANGE...

    Really? It clearly says "TO REVERSE INTERCHANGE RED AND YELLOW LEADS" on the nameplate.
  3. Replies
    21
    Views
    1,156

    I don't think that it is a 9C lathe, but an...

    I don't think that it is a 9C lathe, but an earlier 9" Workshop lathe. I think that the only place to have the oilers was the headstock.

    I have this oil chart from 1934 that went with my...
  4. Replies
    21
    Views
    1,156

    Most of the Gits oilers were pressed in. What is...

    Most of the Gits oilers were pressed in. What is the size of the hole in the HS? I might have some oilers you can pick up.
  5. Replies
    162
    Views
    77,236

    The TM belt is approximately 0.1" thick and I...

    The TM belt is approximately 0.1" thick and I WILL grind about a 3" lap on both parts. Walmart has a 3.7oz tube sold by Zoro for about $5.5 with free delivery - can't beat that!
  6. Replies
    162
    Views
    77,236

    I've got some old treadmill belts that I have...

    I've got some old treadmill belts that I have been wanting to use as a drive belt (after they are cut to size). I was going to use a Loctite product to glue the ends together, but the stuff costs...
  7. Replies
    1
    Views
    271

    What 9" (give us the model number)? You really...

    What 9" (give us the model number)?

    You really do need to post pictures with your inquiry.

    My guess is that it is either an early oil passageway to oil the shaft installed by the factory or a...
  8. Jim, What size lathe is that? Did you make...

    Jim,

    What size lathe is that? Did you make the bracket stud (the pin with the square head)? If so, what size did you make the flats?
  9. The closer is supposed to be a light press fit...

    The closer is supposed to be a light press fit into the spindle - it should rotate WITH the spindle. If your attempts to obtain the correct gear, you could make a sleeve that accomplishes the same...
  10. People have operated the collet closer WITHOUT...

    People have operated the collet closer WITHOUT the special gear. In fact, the person starting that thread was operating quite well without that gear. See the pics further down the thread and you'll...
  11. It's not a collar, but an extended gear that...

    It's not a collar, but an extended gear that presses onto the spindle. The end of the collet closer then is light pressed into the extended gear.

    Go here to get a .PDF of the collet closer that...
  12. Replies
    25
    Views
    2,004

    Wow! Looks like you got most of the change...

    Wow! Looks like you got most of the change gears!

    What's in the blue box?
  13. Hey, Torch, Without pictures, it really didn't...

    Hey, Torch,

    Without pictures, it really didn't happen!
  14. Replies
    27
    Views
    4,956

    The original post is over 7 years old. I doubt...

    The original post is over 7 years old. I doubt that any remain.
  15. Replies
    27
    Views
    4,956

    What you need is in HTRAL.

    What you need is in HTRAL.
  16. Replies
    6
    Views
    1,031

    It's possible, but you would need more...

    It's possible, but you would need more information than is available. The number on the QCGB is just a UNIT NUMBER, which is basically a version number. With the version number info (date, change...
  17. Replies
    6
    Views
    1,031

    Does your lathe have power crossfeed? If not,...

    Does your lathe have power crossfeed? If not, you may have a frankenlathe - a lathe cobbled together from parts of others. The "NCR" stands for 9", standard change gears, and regular spindle hole,...
  18. Replies
    1
    Views
    504

    Probably want a j33. The others are larger than...

    Probably want a j33. The others are larger than the big end of a #2 Morse taper. Just find a good chuck, then a good MT#2 arbor and match the attachment taper styles.
  19. Thread: QGC speed plate

    by SLK001
    Replies
    2
    Views
    654

    User jkull has been making reproductions of SB...

    User jkull has been making reproductions of SB plates and stuff like that. Check him out.
  20. Replies
    5
    Views
    1,153

    The problem with doing it this way is that you...

    The problem with doing it this way is that you can only braze/weld from the edges. This will result in a very weak repair. If you build up with CI rod, your repair is attached across the entire...
  21. Replies
    4
    Views
    880

    What has happened to pictures on this site? You...

    What has happened to pictures on this site? You used to be able to post decent sized pics, but lately, all you get is crappy 320x240 resolution pics. I guess that the software is automatically...
  22. Replies
    5
    Views
    1,153

    Instead of doing dentistry, you should build up...

    Instead of doing dentistry, you should build up the area with the broken tooth with a cast iron rod, then shape the resulting glob into the correct tooth form.
  23. Replies
    5
    Views
    611

    It is the other way around. The older machines...

    It is the other way around. The older machines have "OIL" for Type C oil and the newer machines have "GREASE" for the teflon grease. The only other place for grease would be the motor bearings IF...
  24. Replies
    9
    Views
    1,443

    I like the South Bend base that he has - lots of...

    I like the South Bend base that he has - lots of drawers for storage. I don't like the wheels, because the lathe will never be level. Yes, it's nice to be able to roll around and out of the way,...
  25. Thread: 10k Help!

    by SLK001
    Replies
    5
    Views
    878

    More probably bronze spindle bearings. +1 on the...

    More probably bronze spindle bearings. +1 on the rebuild package, even if you aren't going to rebuild. The guide by ILION Industrial Services will include how to check/adjust the spindle bearings. ...
Results 1 to 25 of 319
Page 1 of 13 1 2 3 4