Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: memoryman

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Okuma&Howa MILLAC 65V with Fanuc 15MA parameters needed

    My customer lost all data and needs NC+PMC parameters.Anyone with the same or very similar machine willing to help?
    Thanks
  2. Replies
    5
    Views
    802

    The FS11 had rigid tapping as an option. Requires...

    The FS11 had rigid tapping as an option. Requires Canned Cycle option. May be software version dependent
  3. Replies
    4
    Views
    3,436

    The answer is "maybe". The optional 'rack' can...

    The answer is "maybe".
    The optional 'rack' can be upgraded at relatively low cost. The control most likely needs additional system software; what is your software version?
  4. AFAIK, all Fanuc control from the 16A/18A onward...

    AFAIK, all Fanuc control from the 16A/18A onward used a small lithium battery in the power supply, accessible from the front.
  5. Replies
    2
    Views
    816

    We specialise in upgrading many controls. We...

    We specialise in upgrading many controls. We upgrade the 1A series, but not yet the iB. Send me an email [email protected]
  6. Replies
    27
    Views
    3,355

    I wanted to discuss upgrading your 31i-A5...

    I wanted to discuss upgrading your 31i-A5 controls with you. Send me a pm if you are interested.
    Bill
  7. Replies
    27
    Views
    3,355

    Vancbiker: send me a pm.

    Vancbiker: send me a pm.
  8. Replies
    27
    Views
    3,355

    1: MEMEX used to be a dealer for our products; no...

    1: MEMEX used to be a dealer for our products; no more.
    2: the maximum USABLE part program memory is 2 Mbytes. It is NOT possible to do it yourself. We are working on a product for these controls.
  9. Replies
    27
    Views
    3,355

    I believe that we already discussed this?

    I believe that we already discussed this?
  10. Replies
    5
    Views
    1,123

    Is the motion card made by Delta Tau? Which model...

    Is the motion card made by Delta Tau? Which model #?
  11. Correction: the 3-digit model means it has MMC...

    Correction: the 3-digit model means it has MMC (Man-Machine Control), which is not necessarily Windows based.
    The 0,10,11,12 and 15 series date from ~1986,but could be had with MMC.
    Your 160i...
  12. This is mainly correct. However, even the...

    This is mainly correct. However, even the 16/18/20/21 i-series have two versions: iA and iB. The iA was manufactured from ~1998 through ~2003. The iB series was manufactured from ~2003 to ?
    Even...
  13. If your memory option parameters are for more...

    If your memory option parameters are for more memory than physically installed, you will get a Ram Parity alarm. Can you publish a photo of the top of the memory board, as well as a list of your...
  14. We have almost all options. Send a pm with your...

    We have almost all options. Send a pm with your control model and software version.
  15. The actual spindle speed display is an option....

    The actual spindle speed display is an option. Depending on you System Software version, that option may be simply turned on. It may also needed additional eproms.
    What is your software version?
  16. The MODE switch assignment is fixed. mode switch...

    The MODE switch assignment is fixed.
    mode switch from left to right DIAG #41:
    KEY EDT MEM TAPE MDI JOG HAN STEP
  17. Replies
    2
    Views
    959

    I have never done this on the FAPT control....

    I have never done this on the FAPT control.
    First, have you entered the OPTION parameters correctly? This is done in the IPL mode.
    Then, all NC params are done first, before the PMC param.
  18. Good reply. Magnets can get demagnitised by...

    Good reply.
    Magnets can get demagnitised by excess heat and physical shock, so if you want to disassemble a stepping motor or anything, don't bang or jerk the magnets.
  19. What procedure did you use for the memory...

    What procedure did you use for the memory upgrade? Who did it, who sold it, what instructions?
  20. Your problem is likely in the manner of the...

    Your problem is likely in the manner of the memory upgrade.
    Who did it?
    We may have the correct Sigma procedure for that.
    If you can't change modes, your ladder is probably not running.
  21. Starting with the newer iB control (around 2005),...

    Starting with the newer iB control (around 2005), Fanuc did not store or display the option parameters in sram but in flash. The FROM (flash and sram) module would therefore retain the options, even...
  22. Replies
    19
    Views
    8,014

    The issue is the driver; not all pc card...

    The issue is the driver; not all pc card manufacturers had that working.
    I use a old WIN2k laptop and have no problems with various makes of pc cards. Never used an adapter.
  23. Replies
    19
    Views
    8,014

    All controls after the 15A and 16/18A have the...

    All controls after the 15A and 16/18A have the ability to save restore the info stored in flash and sram. This is a simple operation and is done through the BOOT screens. The SYSTEM files can also be...
  24. Replies
    24
    Views
    3,388

    Cambridge Ontario, Canada? We are

    Cambridge Ontario, Canada? We are <1hour from there.
  25. Replies
    24
    Views
    3,388

    The Fanuc 11M has slow communications, and mold...

    The Fanuc 11M has slow communications, and mold makers complain about it's inability to feed the motion info fast enough.
    I don't know that particulat machine, and if Machinery_E is correct, you may...
Results 1 to 25 of 32
Page 1 of 2 1 2