Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Nikolaiownz

Page 1 of 6 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    51
    Views
    2,297

    I will see how krocket it is next time I get in...

    I will see how krocket it is next time I get in the shop [emoji28]

    Sendt fra min EML-L29 med Tapatalk
  2. Replies
    51
    Views
    2,297

    It can point to the moon I don't care. As long as...

    It can point to the moon I don't care. As long as I turns fairly straight [emoji23][emoji23]

    Sendt fra min EML-L29 med Tapatalk
  3. Replies
    51
    Views
    2,297

    Yes it's weird. If I remove the gap the spindel...

    Yes it's weird. If I remove the gap the spindel will be off again I guess. Kind of weird to do it this way.

    Sendt fra min EML-L29 med Tapatalk
  4. Replies
    51
    Views
    2,297

    You turn one lose and tighten the other one more...

    You turn one lose and tighten the other one more to adjust. And then when you turn straight you tighten the lose one back.

    Sendt fra min EML-L29 med Tapatalk
  5. Replies
    51
    Views
    2,297

    Yes they are pushing between headstock and ways...

    Yes they are pushing between headstock and ways as far as I know. I think it's able to flex between the ways and the gearbox.



    Sendt fra min EML-L29 med Tapatalk
  6. Replies
    51
    Views
    2,297

    I don't think you have to losen the spindel and...

    I don't think you have to losen the spindel and gearbox to adjust here. I think it's meant to just brute force the spindel alligenment. I think it's made to be able to flex there. Aslong as you have...
  7. Replies
    51
    Views
    2,297

    These two bolts are for adjusting. It's now...

    These two bolts are for adjusting. It's now turning a taper under 0.01mm over 100mm. And the ways are still level.

    It's now straight as an arrow. Pretty good for an amateur [emoji23]

    Thanks...
  8. Replies
    51
    Views
    2,297

    I am sure it was bumped. I replaced the chuck...

    I am sure it was bumped. I replaced the chuck that was on it when I got it because it was a mess

    Sendt fra min EML-L29 med Tapatalk
  9. Replies
    51
    Views
    2,297

    Yep I saw that aswell. But they are very hard to...

    Yep I saw that aswell. But they are very hard to get to. I will see about it tomorrow when I got time. Way to busy at the shop so I had to wait a few days [emoji44]

    Sendt fra min EML-L29 med...
  10. Replies
    51
    Views
    2,297

    Away from the chuck Sendt fra min EML-L29 med...

    Away from the chuck

    Sendt fra min EML-L29 med Tapatalk
  11. Replies
    51
    Views
    2,297

    I come here for advise because I don't have a...

    I come here for advise because I don't have a clue. Well no shit. If I had a clue I wouldn't be asking.

    Sendt fra min EML-L29 med Tapatalk
  12. dosent look like there is any proper trained...

    dosent look like there is any proper trained mazatrol people.. i see why... this control is fairly weird if you ask me.. i forsure is never gonna get another mazak :p
  13. Replies
    51
    Views
    2,297

    i checked in the flat way with my precision level...

    i checked in the flat way with my precision level and ontop of the saddle all the way down the ways every 100mm aprox.. there where very little flex( not over 0.02/m).

    i tryed to see if i had a...
  14. Replies
    51
    Views
    2,297

    i will not twist the ways for compensation...

    i will not twist the ways for compensation forsure.. if thats the only way i will sell it.. i know its a used lathe but the ways looks good but they do have some rise at the bridge.. i will check...
  15. Replies
    51
    Views
    2,297

    that might be the problem.. i dont think its easy...

    that might be the problem.. i dont think its easy to lift this spindel off.. and the bolts are not easy to access.

    Can the problem be the way bridge under the spindel? there seem to be 0.05 lift...
  16. Replies
    51
    Views
    2,297

    Sadly i seem to be missing a manual about...

    Sadly i seem to be missing a manual about headstock adjustment.. i only got a little start/operating manual and a parts list manual.
  17. Replies
    51
    Views
    2,297

    it is a 0.02/m and the ways are leveled all the...

    it is a 0.02/m and the ways are leveled all the way... yep 0.15 over 100 mm is alot.. that would not be a good idea to compensate in the ways.. i am sure its the spindel thats out of wack.. i just...
  18. Replies
    51
    Views
    2,297

    i already did the two collar test with mic on the...

    i already did the two collar test with mic on the turned shaft you see in the pic. the indicator in picture was just to see if my ways was wacked or was parallel with the turned collars on the...
  19. So there is no way to teach it inside the...

    So there is no way to teach it inside the mazatrol program editor? i have to go outside to command screen and then go back to the mazatrol program editor and type it down and then write it into the...
  20. Replies
    51
    Views
    2,297

    265116265117265118

    265116265117265118
  21. Replies
    51
    Views
    2,297

    265111265112265113265114265115

    265111265112265113265114265115
  22. Noone that can tell me how to set wpc origin in a...

    Noone that can tell me how to set wpc origin in a mazatrol program? :willy_nilly:

    is still havent figured out how to tech/touch with my 3d taster other than in the g54 offset and manually put them...
  23. Replies
    51
    Views
    2,297

    TOS SN500S Spindel aligenment

    Hello

    I bought a tos sn 500s lathe that had a few problems.

    Ive leveled the lathe fairly good and it still turns a taper of 0.15mm over 120mm right infront of the spindel. that tells me that...
  24. sorry the typo in subject ment wpc

    sorry the typo in subject ment wpc
  25. Mazatrol M32 QPC OR origin problems - cant seem to figure it out.

    Hey

    I cant find anything in the manuals i got.

    Ive been using my mazak with EIA since start but i kinda want to digg into mazatrol. i cant seem to find out how to set my wpc? in the mazatrol...
Results 1 to 25 of 147
Page 1 of 6 1 2 3 4