Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Ohio Mike

Page 1 of 60 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    14
    Views
    1,215

    I found a 62" King listed as weighing 65,000. A ...

    I found a 62" King listed as weighing 65,000. A Morey in the 96" range weighs 95,000.
  2. Looks to be 1967

    Looks to be 1967
  3. Replies
    4
    Views
    726

    In addition to the face of the column look on the...

    In addition to the face of the column look on the front of the knee. Many makers used that location for the SN. Very well could be painted over also...
  4. Replies
    3
    Views
    778

    There places in the headstock that don't drain by...

    There places in the headstock that don't drain by just pulling the plug. If there is any doubt I would pull the headstock cover. A turkey baster is an excellent tool to clean the oil and allow you to...
  5. Replies
    3
    Views
    1,092

    What I see is the same type of wear I see in my...

    What I see is the same type of wear I see in my 12CK however much more extreme. Looks like years of the same user or users slamming the dog clutch into gear. Picture #1 clearly shows the amount of...
  6. Replies
    9
    Views
    872

    Great machines, my favorite to operate. If its a...

    Great machines, my favorite to operate. If its a good machine it should be pretty quiet when operating. Here are some quick instructions if you've never run a K&T. Make sure the motor is running the...
  7. Replies
    24
    Views
    2,356

    I would have loved a No Ramp but it was a bit too...

    I would have loved a No Ramp but it was a bit too pricey for me at the time. My solution was a PJ Hydraulic Quick Tilt. Battery was already there for the tilt just added a 10K winch. I call it the...
  8. Replies
    24
    Views
    2,356

    Another to consider is Air-Tow Air-tow Trailers...

    Another to consider is Air-Tow
    Air-tow Trailers
  9. Replies
    11
    Views
    1,147

    Buy a phase converter and be done with it. Why...

    Buy a phase converter and be done with it. Why downgrade to crappy single phase motors
  10. Replies
    11
    Views
    1,218

    I remember the start of that rabbit hole! That...

    I remember the start of that rabbit hole! That was about 20,000 lbs ago. :crazy::D
  11. Replies
    5
    Views
    1,162

    How about... Smith & Mills 25" Metal Shaper...

    How about...

    Smith & Mills 25" Metal Shaper
    Plain Table Model with shaper vise
    7.5 HP 3 Phase Motor (check HP on tag should be 7.5 or 10 HP)
    Ran when removed from service
    Seller can load open...
  12. Replies
    11
    Views
    1,218

    No fancy names or models in those days. Buffalo...

    No fancy names or models in those days. Buffalo called this drill a 16" Floor model Production Drill

    Its in Catalog 801 circa 1929
    http://vintagemachinery.org/pubs/129/4907.pdf
    Go to page 27 in...
  13. From your side of the coin it looks like you are...

    From your side of the coin it looks like you are great employee. If you really want to cause the bosses brain to explode ask him what you need to do to be a better employee and what skills they would...
  14. Replies
    10
    Views
    2,064

    Although an auction house "aka agent" can sell...

    Although an auction house "aka agent" can sell "as is" no warranty etc they can not under any circumstance sell something that the seller does not own. Auction laws very by state and in the US pretty...
  15. Both of my K&Ts are very quiet, much more quiet...

    Both of my K&Ts are very quiet, much more quiet than the BP which makes a heck of racket. They are a real joy to use.
  16. The quill feed on the 2HL is so slow it will be...

    The quill feed on the 2HL is so slow it will be useless for drilling. You would need to use the knee. Unlike a BP where you can plug reverse the head with the drum switch the K&T only runs in...
  17. May have found him in the 1940 census. State of...

    May have found him in the 1940 census.
    State of Ohio, Hamilton County, Springfield Township, Greenhills Village

    For those hard core folks. Follow the link and them Jump to page 36...

    Search...
  18. Replies
    181
    Views
    12,817

    A couple of years ago was told about a guy that...

    A couple of years ago was told about a guy that was a an awesome welder. Not unusual to hear but then I hear that again from someone else a few months later that he could weld absolutely anything....
  19. Replies
    31
    Views
    3,250

    But when can you buy them? I don't see them...

    But when can you buy them? I don't see them anywhere. Anyone gotten their hands on a pair?
  20. Replies
    1
    Views
    709

    Just noticed you posted in the the heavy iron...

    Just noticed you posted in the the heavy iron section, it should really be in the Antique Machinery and History forum.
  21. Yes that's it. Don't know that its any better...

    Yes that's it. Don't know that its any better than the others listed. I choose that one initially because it would arrive in the time frame I needed it. The only issue I had with it was the pipe...
  22. Some pic's of a recent move I did. Pick the...

    Some pic's of a recent move I did.

    Pick the machine up. Doable with a bar but recently invested in a cheap ebay toe jack. Best $100 this year. Seriously :cool:
    257941

    Then we built pallet...
  23. This is easiest done with a hydraulic power tilt...

    This is easiest done with a hydraulic power tilt trailer but I've done it with plain Sunbelt Rentals gravity pan tilt with a rolling floor jack. You don't need to pick up the mill very far, just...
  24. Replies
    12
    Views
    1,506

    Its an older Super Chuck. Even older than this...

    Its an older Super Chuck. Even older than this were the ones with the knurled sleeve.
  25. Replies
    15
    Views
    1,705

    Not sure about this machine but the headstock on...

    Not sure about this machine but the headstock on the 12CK has places that won't drain fully with the plug out. The quick fix is to use a turkey baster to suck up that oil and squirt it over where it...
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4