Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: leeko

Page 1 of 52 1 2 3 4

Search: Search took 0.02 seconds.

  1. Fm50 arrived in great shape, thanks Rusty! Lee...

    Fm50 arrived in great shape, thanks Rusty!

    Lee

    Sent from my SM-N960U using Tapatalk
  2. I'll happily take the $50 teco 2hp unit ...

    I'll happily take the $50 teco 2hp unit

    Thanks,

    Lee

    Sent from my SM-N960U using Tapatalk
  3. Replies
    10
    Views
    620

    I have a hardinge TM mill with a 2 speed motor. I...

    I have a hardinge TM mill with a 2 speed motor. I wanted continuously variable speed, so I wired a vfd to the high speed winding as you mentioned. I'm not aware of any simpler/better ways to do it,...
  4. Replies
    2
    Views
    293

    Thanks! I thought I had them backed out pretty...

    Thanks!

    I thought I had them backed out pretty well, but I went back around and backed then out until they hit the retaining ring. Now the indexer clicks audibly when the pin engages, and all play...
  5. Replies
    2
    Views
    293

    HV-4N style indexer - worn or user error?

    Hi everyone,

    I acquired a used HV-4N style indexer recently, and I pulled it apart to give it a good cleaning before using. Now that's it's back together, everything works as it should. But, I've...
  6. Replies
    10
    Views
    620

    I'm not sure I understand your setup. Is the...

    I'm not sure I understand your setup. Is the 20vdc motor your power feed motor?

    What's your spindle motor? If you're planning to run a vfd, the motor needs to be a 3 phase ac motor with the...
  7. Yes, I realized after I posted that the mandrel...

    Yes, I realized after I posted that the mandrel would be tiny.

    Could the piece be turned in the chuck, and the bore created with an center cutting endmill held in the toolpost?

    Sent from my...
  8. I'm missing something here. OP needs to make an...

    I'm missing something here. OP needs to make an 11mm long bushing with concentric bore that deviates not more than 0.001" end to end. That's not especially close tolerance - why does it need to be...
  9. Chuck the rod in your lathe. Drill and ream the...

    Chuck the rod in your lathe. Drill and ream the ID to finished size. Remove from the chuck. Place another piece of stock between centres and turn a mandrel to a light press fit, or a sliding fit with...
  10. :) Sent from my SM-N960U using Tapatalk

    :)

    Sent from my SM-N960U using Tapatalk
  11. Machinery leveling feet most suited to which machine?

    Hi all,

    I recently picked up a package of 4 nice 5" machinery levelling feet. They are marked Gislaved, and are a hard rubber with threaded rods that go through them. I wasn't particularly looking...
  12. Great, thanks! Sent from my SM-N960U using...

    Great, thanks!

    Sent from my SM-N960U using Tapatalk
  13. Ok, good to know. Thanks for the examples! Lee...

    Ok, good to know. Thanks for the examples!

    Lee

    Sent from my SM-N960U using Tapatalk
  14. Here's the number on the top of the K&T head's...

    Here's the number on the top of the K&T head's mounting bracket. Looks like 6-5727. Does that help place the bracket or model it goes to?

    Thanks

    Sent from my SM-N960U using Tapatalk...
  15. Thanks Jim! Lots of Cincy #2 stuff there, but...

    Thanks Jim!

    Lots of Cincy #2 stuff there, but I didn't see a #2 at the site. Would these go to a monoset also? There was one of those listed....

    Lee

    Sent from my SM-N960U using Tapatalk
  16. Ok, I picked up the lot. Here's what there was: ...

    Ok, I picked up the lot. Here's what there was:

    Vertical head for cincinatti 420-16-20HD
    50 taper drive gear for above

    Vertical swivel head for K&T, haven't figured out the model it's for yet...
  17. Awesome, thanks! Sent from my SM-N960U using...

    Awesome, thanks!

    Sent from my SM-N960U using Tapatalk
  18. Advance rotary cross slide height and rigidity

    Hi everyone

    I have a van Norman 26 mill with a factory installed 7" riser. With the mill head in horizontal position, the riser prevents smaller cutters from getting close to the table.

    I...
  19. Thanks for taking the time to post pictures. You...

    Thanks for taking the time to post pictures. You may remember me asking a bunch of questions about the swivel head K&T, as I owned one up until last year :)

    I'm still not seeing it though - the...
  20. Hi John, I think we're talking about different...

    Hi John,

    I think we're talking about different parts - the first picture I posted (gray blue milling head) appears to be this, which I found in the K&T S12/S15 brochure after you suggested K&T:
    ...
  21. Jim, that's great information thanks! Can't...

    Jim, that's great information thanks!

    Can't wait to pick this stuff up. I'm pretty sure one of the additional workheads in the lot will bolt onto the radius grinding attachment.

    I'm starting...
  22. For example, Here's another piece in the same...

    For example,

    Here's another piece in the same lot. I'm guessing it's a grinder accessory, but no idea beyond that...

    There also appears to be 3 or 4 more grinder workheads like the one Jim...
  23. Hi Brian, I'll likely have some surplus stuff,...

    Hi Brian,

    I'll likely have some surplus stuff, as there were quite a few items in the lot. I took a chance on it because I'm looking for a universal head for the van Norman and a vertical head for...
  24. Awesome, thanks! I wonder if I can make it fit on...

    Awesome, thanks! I wonder if I can make it fit on my tiny import T&CG :-p

    Sent from my SM-N960U using Tapatalk
  25. Ok good to know I'm guessing it will be...

    Ok good to know

    I'm guessing it will be adaptable. Question will be how much work it will take :-p

    The configuration of the head looks very similar to the van Norman universal subhead I was...
Results 1 to 25 of 1278
Page 1 of 52 1 2 3 4