Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: SIP6A

Page 1 of 60 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    29
    Views
    736

    Short answer, No.

    Short answer, No.
  2. It would be more believable if the story stated...

    It would be more believable if the story stated where he was from. This was posted by a Mike Newbert on facebook. I stopped counting after fifty Mike Neberts on Facebook. The boys name is Hunter...
  3. Replies
    11
    Views
    1,081

    So in other words he's a typical used machinery...

    So in other words he's a typical used machinery dealer.
  4. If you go to there website, they say that there...

    If you go to there website, they say that there preparing to close, however if you click on "other publishers" it will take you to a list of 11 publishers and booksellers of the same type of material.
  5. Replies
    76
    Views
    6,013

    Congratulations!! I have enjoyed following...

    Congratulations!!

    I have enjoyed following along, keep posting as you continue to bring this machine back to life.
  6. Replies
    94
    Views
    4,224

    Donie: Rather than posting here about termite...

    Donie:

    Rather than posting here about termite with no effect, you should start sending letters (I say letters because a letter will get there attention where an email will just be ignored.) to the...
  7. Replies
    30
    Views
    1,727

    Sure it wasn't Gallmeyer & Livingston in Grand...

    Sure it wasn't Gallmeyer & Livingston in Grand Rapids Michigan?
  8. Replies
    4
    Views
    3,225

    The Hauser 324 is the measuring machine the 325...

    The Hauser 324 is the measuring machine the 325 is the jig borer. Would you have a rotary table for a Hauser 325?
  9. Replies
    11
    Views
    1,081

    You can call up the auction co. and ask. I've...

    You can call up the auction co. and ask. I've done that and they don't seem to mind.
  10. Replies
    22
    Views
    1,430

    Cash, I’ve got about 10 lb’s of red lead. I could...

    Cash, I’ve got about 10 lb’s of red lead. I could send you a couple of lb’s if you could use it.

    Also you could go to a chemical supply house to get these chemicals. The chemical name for lamp...
  11. Replies
    6
    Views
    710

    ............

    ............
  12. Replies
    17
    Views
    907

    I would never consider a gear puller an...

    I would never consider a gear puller an automotive tool. but I have found OTC tools very well made and have worked very well on machine tools.
  13. Replies
    11
    Views
    1,640

    Screw machine is quite interesting, but what's...

    Screw machine is quite interesting, but what's the flywheel on in the background?
  14. Replies
    13
    Views
    1,128

    Thanks! I'll get in touch when it gets closer to...

    Thanks! I'll get in touch when it gets closer to my getting on the road.
  15. Replies
    13
    Views
    1,128

    I'm going to be heading up that way in a couple...

    I'm going to be heading up that way in a couple of weeks. If I stop to have a look and point at a machine and ask "How much" will the owner put a price on it?
  16. Replies
    27
    Views
    1,881

    Does this have a rubber gasket as part of it? ...

    Does this have a rubber gasket as part of it?

    If so I would also suggest KROIL or any light oil and dissolve the rubber gasket. It will take a few days of soaking but it will come apart.
  17. Replies
    29
    Views
    2,405

    Well buying a machine from the gub'mint (Yankee...

    Well buying a machine from the gub'mint (Yankee spelling) does have a certain Je ne sais quoi quality about it.
  18. Replies
    6
    Views
    438

    Here's the link to the eBay auction with an...

    Here's the link to the eBay auction with an opening bid of $700.00. See was that so hard?

    Harig Air-Flo | eBay
  19. Replies
    23
    Views
    1,394

    make a dike pour lead in take out when solid...

    make a dike pour lead in take out when solid measure angle.
  20. Replies
    29
    Views
    2,405

    That was probably because the winning bidder had...

    That was probably because the winning bidder had his bid in at $3550.00 The back bidder was in at $2995.00 Auctions being the scam they are the auction took the higher number as the next bid.
  21. Replies
    29
    Views
    2,405

    It's not....

    It's not....
  22. Replies
    3
    Views
    442

    You would think that an outfit like Hispano -...

    You would think that an outfit like Hispano - Suiza could design a better looking car than what they came up with.

    As an aside H - S today is one of the world's largest manufacturer of aircraft...
  23. Replies
    7
    Views
    550

    Your expected to be a man about it and pay the...

    Your expected to be a man about it and pay the appropriate rate. If your a grifter you scam everybody for every cent you can and then brag about how you pulled one over on the rubes.
  24. Replies
    11
    Views
    4,853

    Well I spent a pathetic hour or so reading about...

    Well I spent a pathetic hour or so reading about this and he sure comes across as a scam artist. I would say your money is gone and your never going to see it. Have you thought about getting law...
  25. Replies
    7
    Views
    550

    I have sold catalogs for years and have had a...

    I have sold catalogs for years and have had a long discussion with our local postmaster. It’s all catalogs doesn’t make any difference how old it is.
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4