Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: bll230

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    6
    Views
    449

    Thanks for checking, On my calculator the...

    Thanks for checking, On my calculator the tan(9degrees 32'=9.533 degrees)*12 = 2.0153.

    For arctan(2*1.000638/12) I get 9.4653 = 9 degrees 27.9'

    Can you check again?

    Even before I saw...
  2. Replies
    6
    Views
    449

    1950's collet question

    I got a manual for a Hamilton hobber, because who doesn't like reading old hobber manuals? It includes a print of the work spindle so the necessary collet holders can be made by the user. Here it...
  3. Replies
    15
    Views
    882

    I have been out of town, got home and looked at...

    I have been out of town, got home and looked at my parts diagram of probably square dial MG era, which looks the same as the round dial since both use the larger Reliance motor. Kind of hard to...
  4. Replies
    15
    Views
    882

    The C0 bearings are definitely precision...

    The C0 bearings are definitely precision bearings. In picture 4 of your original post it shows a gasket between the end cap and the pulley shaft. The square dial doesn’t have that gasket since the...
  5. Replies
    15
    Views
    882

    I had one other idea while I was considering...

    I had one other idea while I was considering bearing availability, although not directly applicable to the current situation. A double row angular contact similar to the spindle rear bearing could...
  6. Replies
    15
    Views
    882

    You are correct, with your information I should...

    You are correct, with your information I should have prefaced my answer with "I have a square dial." I'm confused with the V suffix, the snap ring opposite normal side. Radial bearings are...
  7. Replies
    23
    Views
    3,531

    Lectrician1 made his own clamp and rod, maybe he...

    Lectrician1 made his own clamp and rod, maybe he would be willing to make a run of them for others.
  8. Replies
    15
    Views
    882

    I am going to go out on a limb, and suggest you...

    I am going to go out on a limb, and suggest you are using normal radial bearings, not an angular contact pair.

    MRC 209 SFF comes up as a radial bearing with a certain grease and a steel retainer....
  9. Replies
    1
    Views
    324

    reduction gearbox bearing set - 10EE

    I have commented that I replaced all the bearings in my square dial 10EE. That wasn't quite true, the large bearing pair in my reduction gearbox seemed good so did not replace it, but in using my...
  10. Replies
    6
    Views
    443

    This is from the round dial manual. Check on...

    This is from the round dial manual. Check on Ebay for the filter replace kits. Some of the auctions in the past showed an instruction page in the kits.

    When I reassembled my pump I used 1/8 inch...
  11. Replies
    6
    Views
    569

    I raced bicycles when I was younger and faster,...

    I raced bicycles when I was younger and faster, and I have all the Park wrenches. I got this one for the workshop, though. Once they are loosened from 50 years of crud, I left pins in them to get...
  12. Replies
    11
    Views
    1,147

    Larry, that is some impressive pricing. ...

    Larry, that is some impressive pricing. Coincidentally, I just recently bought the center from Ted. My Barber Colman project was delayed by my Monarch 10EE project. I made the displayed driver,...
  13. The hex head bolt that you refer to at the top of...

    The hex head bolt that you refer to at the top of this thread is in fact a socket head bolt that is recessed like the others on my 1956.

    Also, relative to the thrust bearings, mine were good so...
  14. Replies
    8
    Views
    839

    ZK can make them for you, or if you buy me a hob...

    ZK can make them for you, or if you buy me a hob I'll make them. I still haven't been able to find a 32 Dp 14 1/2 PA hob on ebay. Just got a beautiful brand new Gleason 36 Dp hob for $25,...
  15. Replies
    8
    Views
    839

    ZK's instructions should explain all, look at my...

    ZK's instructions should explain all, look at my pics and explanation here as well.

    Metric threading gears - 10EE square dial
  16. Replies
    8
    Views
    839

    Apple has a an issue with the pics not rotating...

    Apple has a an issue with the pics not rotating properly. Here is a solution. When I download pictures from the iphone or ipad to the mac I then duplicate the picture (right click, duplicate)...
  17. Replies
    13
    Views
    904

    Does this help? 273104

    Does this help?

    273104
  18. Use a lathe,(hopefully you have another one) to...

    Use a lathe,(hopefully you have another one) to make a large aluminum/brass ring that fits precisely around the diameter where the pin is, drill and tap for a pusher bolt, and then cut in half to...
  19. Tach disassembly question - 1956 10EE square dial

    While my lathe is running there is a very slight rubbing noise coming from the tach. Does anyone have any suggestions on disassembling the tach?

    I read Focus's thread,
    ...
  20. Replies
    17
    Views
    1,510

    Sikorsky in Stratford, Ct. was/is the same. 4x4...

    Sikorsky in Stratford, Ct. was/is the same. 4x4 sections on end. Had been there since WW 2 or so.
  21. As an (hopefully talented) aeronautical engineer...

    As an (hopefully talented) aeronautical engineer with a deficient ability to understand EE stuff, thank you very much for this work.
  22. Replies
    8
    Views
    744

    For My 10EE I had great luck getting bearings...

    For My 10EE I had great luck getting bearings from LocateBB on Ebay. I think every bearing I searched for they came up as a seller(except the spindle bearings). I did have to message them so when I...
  23. Replies
    5
    Views
    592

    I've got one, I just need collets for it.

    I've got one, I just need collets for it.
  24. Willy, you mention another gear source. I doubt...

    Willy, you mention another gear source. I doubt Monarch makes gears any longer. If they do not have leftover inventory from decades ago, they probably contract with a gear shop. As far as price...
  25. I am the owner of Bill’s former small frame...

    I am the owner of Bill’s former small frame Reliance, Presently in my lathe. My original motor with the smoked armature I took to a motor rebuilding shop and was quoted minimum $1500 for a rewind,...
Results 1 to 25 of 495
Page 1 of 20 1 2 3 4