Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Bill D

Page 1 of 60 1 2 3 4

Search: Search took 0.08 seconds.

  1. Not a recommendation since I have never used them...

    Not a recommendation since I have never used them but Aragon in San Leandro buys and sells used machine tools. They advertize they move them as well.
    Bill D.

    Home
  2. Replies
    49
    Views
    2,280

    I heard the CDC was overruled so they could bring...

    I heard the CDC was overruled so they could bring infected Americans into the USA on a planeload of non infected people as well. I will not be a trump basher here I will just say the State...
  3. Thread: Cut out oblong

    by Bill D
    Replies
    19
    Views
    544

    Grab it in vise grips. Drive about 25mph on a...

    Grab it in vise grips. Drive about 25mph on a paved road, concrete if possible. lean out door and apply work to the ground with firm pressure Check for fit every 200 feet or so. Be careful to...
  4. Replies
    10
    Views
    786

    Could you stack up some railcar truck springs. ...

    Could you stack up some railcar truck springs. they may b similar size.
    Bil lD
  5. Thread: Cut out oblong

    by Bill D
    Replies
    19
    Views
    544

    A shaper or horizontal mill would be the classic...

    A shaper or horizontal mill would be the classic way to go. Will any of it remain full round or is it oval all the way?
    Bill D
  6. Replies
    188
    Views
    6,872

    That is a sink plunger not a toilet plunger. You...

    That is a sink plunger not a toilet plunger. You do know the difference don't you? On this site you are expected to know your tools.
    Bil lD
  7. Replies
    35
    Views
    1,714

    Evaporust is mostly EDTA and some stuff to...

    Evaporust is mostly EDTA and some stuff to maintain the ph.
    Can you throw the finished parts in buckets or bags and fill the bucket with inert gas such as CO2 or nitrogen. Even car exhaust should...
  8. Replies
    7
    Views
    526

    Same applies to gear tooth counts. Folks here...

    Same applies to gear tooth counts. Folks here claim they can see it on lathe spindle runout as various slight diffferences add up in roller bearings casing a cyclic shift. Theory is roller outer...
  9. Replies
    11
    Views
    1,006

    I have seen pictures of lathes made by Rolls...

    I have seen pictures of lathes made by Rolls Royce for factory use. I think they made 6-12 total.
    Bill D.

    Rolls Royce Lathe
  10. Replies
    21
    Views
    1,279

    Rats of NIMH do not use those supplements ans...

    Rats of NIMH do not use those supplements ans there frontal lobes are just fine. Smarter then the average rat. Much smarter then the average elected official.
    Bil lD
  11. Replies
    21
    Views
    1,279

    Well easier then what I saw on the news today. ...

    Well easier then what I saw on the news today. IV vitamins for the hollywood set. Also easier then what the FDA warned about roughly one year ago. blood transfusions using teenager blood. Supposed...
  12. Replies
    21
    Views
    1,279

    I wonder if trump drinks brass sweeping water for...

    I wonder if trump drinks brass sweeping water for that healthy yellow glow?
  13. Replies
    21
    Views
    1,279

    Gee, I could sell floor sweepings as iron...

    Gee, I could sell floor sweepings as iron supplements at the local farmers market. Maybe aluminum or titanium chips to lose weight. A better diet then all that fatty spam.
    Bill D.
  14. Replies
    13
    Views
    761

    Bevel the edge and call it a feature. That is...

    Bevel the edge and call it a feature. That is how older wood panels and glass sheets were done.
  15. Replies
    5
    Views
    375

    Any push to connect, momentary contact, switch...

    Any push to connect, momentary contact, switch should work.
    Bil lD
  16. Replies
    48
    Views
    3,567

    Maybe they need some wood or metal serving trays...

    Maybe they need some wood or metal serving trays to go with the table. How about making some chairs to match.
    Bil lD
  17. Replies
    7
    Views
    718

    What about leather?

    What about leather?
  18. Replies
    521
    Views
    46,271

    People from out of the area may look at Tesla pay...

    People from out of the area may look at Tesla pay and think it is high but housing costs there are fairly high. A 3 bedroom house probably starts around 600-750,000. So property taxes could be...
  19. Replies
    38
    Views
    3,621

    I doubt it will be that quick and easy when it is...

    I doubt it will be that quick and easy when it is mounted in a massive aluminum plate heatsink.
    Bil lD
  20. Replies
    10
    Views
    1,157

    I suspect the brake solenoid is single phase so...

    I suspect the brake solenoid is single phase so it can be supplied outside of the vfd. probably 108-120 volts or 220-240. It should not be vfd powered maybe switched through the vfd auxillary...
  21. Replies
    38
    Views
    3,621

    If you go with heat you will have to throw a...

    If you go with heat you will have to throw a welders blanket or bricks on the plate to keep in the heat.
    Bil lD
  22. Replies
    38
    Views
    3,621

    Carbide endcutting endmills would be my first...

    Carbide endcutting endmills would be my first choice from my limited experience. Is there any solvent for cured epoxy? How about acid or alum to corrode the steel. A tap destroyer would work well...
  23. Replies
    48
    Views
    3,567

    Purists will complain the legs should have been...

    Purists will complain the legs should have been one piece carved out of tree roots that grew in that shape. That is how ship ribs used to be made. Of course that would add years looking for the...
  24. Replies
    30
    Views
    2,591

    I have read that oak, walnut and mahogany are the...

    I have read that oak, walnut and mahogany are the worst woods for metal contact. They all have high acid content and moisture in the air will cause acid which will rust any metal in contact. I do...
  25. Thread: Antique Planer

    by Bill D
    Replies
    5
    Views
    523

    does anyone still make planners?

    does anyone still make planners?
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4