Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Scruffy887

Page 1 of 58 1 2 3 4

Search: Search took 0.03 seconds; generated 30 minute(s) ago.

  1. Replies
    23
    Views
    1,980

    Zero rake and all should be fine. On the lathe I...

    Zero rake and all should be fine. On the lathe I peck feed and need to pull out completely to clear chips. On the mill the peck distance is about same as drill D to start, dwell peck. I want the...
  2. Perfect job for a laser, apply finish first. 3M...

    Perfect job for a laser, apply finish first.
    3M makes some really good abrasive brushes in cup and wheel form. And they last a real long time.
  3. Replies
    23
    Views
    1,980

    Hole that deep on a manual lathe with the...

    Hole that deep on a manual lathe with the tailstock will be a major PITA. Drill on the carriage. Parabolic drill to get chips out but grind the cutting edges flat. If not then it will pull for sure...
  4. Any and all, including 317U unobtainium grade....

    Any and all, including 317U unobtainium grade. Really need more info like sketch and punch and die stuff.
  5. Replies
    40
    Views
    3,346

    Almost finished. All smaller drawers are on 100#...

    Almost finished. All smaller drawers are on 100# soft close full extension slides. Big drawer is on 500# full extension slides.
    262869
  6. Replies
    26
    Views
    2,808

    I can't believe I got half way through these...

    I can't believe I got half way through these replies before it dawned on me that these are soft jaws on a vise. Coffee not working this morning.
    Multiple parts stacked in lathe jaws made no sense.
  7. Replies
    31
    Views
    2,777

    Supplier of mine said this. If its going to be...

    Supplier of mine said this. If its going to be late, its Yellow Freight. Not dependable and F them. We will not use them and suppliers are forbidden to use them to ship to us. As a noob I loaded 3...
  8. Replies
    23
    Views
    1,477

    You guyzs forgot unobtainium. Flux capacitor...

    You guyzs forgot unobtainium. Flux capacitor needed w/o gas.
  9. Replies
    4
    Views
    448

    Does it say which side is lowest? Rotate the die...

    Does it say which side is lowest? Rotate the die and see if the problem switches sides. Could also be density differences on the die.
    Try putting the tooling in the middle. You are loading lop sided.
  10. Replies
    10
    Views
    718

    Once the coating is gone the tool is toast....

    Once the coating is gone the tool is toast. Carbide does not hold up to quartz very well. You really want the diamond/metal matrix as per DavidScott and you will need a rougher and a series of...
  11. No offence to DD but listening to failures only...

    No offence to DD but listening to failures only has problems with your perception. I stopped breathing only 89 times an hour at my last sleep study. Report also said I did not tolerate the nasal mask...
  12. Wife and I each drive Ford Focus RS AWD hatch...

    Wife and I each drive Ford Focus RS AWD hatch backs. 6 speed, Recaro seats, Brembo brakes, and 350 HP. 4 driving modes, normal, sport, drift, track. In drift mode 80% power goes to the rear and 20%...
  13. Replies
    14
    Views
    1,202

    Granquartz.com or Regentstoneproducts.com Both...

    Granquartz.com or Regentstoneproducts.com
    Both will have plenty of diamond tools. Stay away from any type of chip forming tool unless working with soapstone, marble.
  14. Replies
    26
    Views
    1,686

    Looking at blue circle. Do I see L1, L2, L3 and...

    Looking at blue circle. Do I see L1, L2, L3 and ground at the big relay? 3 phase if so.
  15. Replies
    26
    Views
    1,686

    Not sure about single phase 220/440. That would...

    Not sure about single phase 220/440. That would describe a motor that could run on single phase 440 volts?
  16. Replies
    43
    Views
    2,393

    Skill and Makita worm drives are sold with water...

    Skill and Makita worm drives are sold with water feed adapters just for cutting stone. They work and many stone shops have one because sometimes it is needed, gets them out of a jam. Cut from each...
  17. Replies
    15
    Views
    951

    Your dentist uses UV cured fillings. I have a...

    Your dentist uses UV cured fillings. I have a few. I had a few scratches in my granite counter top that I made to disappear with UV clear. 5 years ago and still cannot find them.
  18. Replies
    30
    Views
    8,872

    You buy tooling according to the jobs that you...

    You buy tooling according to the jobs that you have. No jobs lined up? No tooling needed.
    I am just posting before this thread gets locked.
  19. That is a very thick piece to cut with Nitrogen....

    That is a very thick piece to cut with Nitrogen. Curious why not Oxygen.
  20. Replies
    4
    Views
    941

    Bodor has a small 48 x 54? bed fiber laser that...

    Bodor has a small 48 x 54? bed fiber laser that is fully enclosed. Max Photonics or IPG fiber laser source. Prob any power level up to 3kw? Yes, Chinese company but I bought mine from a US importer...
  21. My new 10 HP Kaeser air tower gets started up...

    My new 10 HP Kaeser air tower gets started up next week.
  22. Replies
    52
    Views
    3,724

    Corded Milwaukee right angle drill, type...

    Corded Milwaukee right angle drill, type electricians and plumbers use. Not even a week. Tore the teeth off the gears.Replaced with a massive Dewalt right angle, type that looks to be made from a...
  23. Replies
    24
    Views
    1,846

    Had a 20 hp Atlas with dryer. 25,000+ hours...

    Had a 20 hp Atlas with dryer. 25,000+ hours before Electronikon controller went tits up. It was not problem free, kept blowing off the air valve when the drier froze up and it fogged the shop with un...
  24. Replies
    18
    Views
    1,792

    I have some name brand magnets and some bought on...

    I have some name brand magnets and some bought on Amazon. All look to be from the same factory/design. Nothing as heavy as you need but they sure come in handy.
  25. Replies
    22
    Views
    2,358

    [QUOTE=Milland;3362277] If that's real Delrin,...

    [QUOTE=Milland;3362277]
    If that's real Delrin, you might find a central "rough zone", which is characteristic of how the material is made. If it's an acetal copolymer, it should be more...
Results 1 to 25 of 1441
Page 1 of 58 1 2 3 4