Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: johnoder

Page 1 of 60 1 2 3 4

Search: Search took 0.26 seconds.

  1. Replies
    6
    Views
    137

    Info on posting photos ...

    Info on posting photos

    https://www.practicalmachinist.com/vb/south-bend-lathes/posting-pictures-south-bend-forum-372508/?highlight=photos

    good luck
  2. No manual but have the WW2 brochure scanned. Can...

    No manual but have the WW2 brochure scanned. Can email same if you want to Private Message me with that address with Norton SG in the subject line
  3. My preference is what is cast into the head...

    My preference is what is cast into the head stock.:D

    Greaves Klusman, or short for Greaves Klusman Tool Company

    And thank you for your consideration

    On Edit:

    Error corrected - thanks Bill
  4. Replies
    3
    Views
    147

    Early twenties Here is "manual" scan ...

    Early twenties

    Here is "manual" scan

    http://pounceatron.dreamhosters.com/docs/hendey/1920-Hendey-manual.pdf

    Here is a write up on their lead screw reverse system - starts at post #17
    ...
  5. Replies
    8
    Views
    406

    Or a simple fab job - flat bar, hub with keyed...

    Or a simple fab job - flat bar, hub with keyed bore, handle to suit - same idea as here though I started with the commonly available forging and this shorty needed a "clutch"

    (for my 36" Ohio...
  6. Replies
    12
    Views
    727

    Bigger ones I turn to 3/4 dia.

    Bigger ones I turn to 3/4 dia.
  7. Replies
    17
    Views
    1,136

    '34 (linked in Post #5) catalog says it went 20...

    '34 (linked in Post #5) catalog says it went 20 to 579 for the 8 speeds. That is about it for top end on those Bronze bearings
  8. They did make such things (HLTS) for the "Heavy...

    They did make such things (HLTS) for the "Heavy 9" (similar bed features to later H10) back in the day (early to mid thirties), but they would have been 7/16" lower compared to Heavy 10

    (H9 was 9...
  9. :nutter: If there was would it not still be 3"...

    :nutter:

    If there was would it not still be 3" too tall?
  10. Replies
    10
    Views
    405

    I have about a hundred B&S cutters that have no...

    I have about a hundred B&S cutters that have no mention of PA - they are just stamped INVOLUTE (since there were OTHER tooth forms in those days - such as EPICYCLOIDAL)

    The point being 14.5 was so...
  11. Replies
    10
    Views
    405

    Both 14.5 Composite and 14.5 Full Depth systems...

    Both 14.5 Composite and 14.5 Full Depth systems have minimum total depth of 2.157 / P

    So 16 DP would be .1348" minimum

    Ref Volume 2 of Buckingham's Manual Of Gear Design
  12. Replies
    92
    Views
    2,939

    Coming up on ten years - no more pets 299784

    Coming up on ten years - no more pets

    299784
  13. A place to start A treatise on milling and...

    A place to start

    A treatise on milling and milling machines .. : Cincinnati Milling Machine Company : Free Download, Borrow, and Streaming : Internet Archive

    have fun

    Might be worth looking...
  14. Replies
    63
    Views
    1,956

    Not especially handy, but the piece to be done...

    Not especially handy, but the piece to be done was larger than the available lathes

    Probably have to scroll UP to get to Post #1
    ...
  15. Replies
    15
    Views
    1,656

    Sturdy Beast (this from 1911 I think) and...

    Sturdy Beast (this from 1911 I think) and incidentally a good shot of the two screw tool post

    299672

    In those days the T/A was on a massive bracket bolted to and positionable on the bed
  16. I'll guess you could put stop collars on the feed...

    I'll guess you could put stop collars on the feed rod and turn off the feed (during compression of spring)
  17. My 3KVA bought new 17 years back has run...

    My 3KVA bought new 17 years back has run "backwards" without issue all that time
  18. Replies
    8
    Views
    406

    Maybe like so (just an illustration - none here)...

    Maybe like so (just an illustration - none here)

    299609
  19. Thread: Photo test

    by johnoder
    Replies
    16
    Views
    899

    Either of the ways to do it described in the...

    Either of the ways to do it described in the oldest posts in this thread work for me (I only post from desktop) - but only if I hit GO ADVANCED first
    ...
  20. Which is more than enough to destroy poor...

    Which is more than enough to destroy poor metallurgy

    THE FORGOTTEN TRAGEDY The 1844 explosion on the USS Princeton shook the presidency of John Tyler | Town And Countymiscellaneous |...
  21. Replies
    2
    Views
    418

    The other thread 1956 13” spindle nose taper ,...

    The other thread

    1956 13” spindle nose taper , what is it?

    ph
  22. In the 1934 catalog page 24 - making it a series...

    In the 1934 catalog page 24 - making it a series O from the early thirties

    http://www.wswells.com/data/catalog/1934_cat_94/1934_cat_94.pdf

    have fun
  23. Replies
    9
    Views
    595

    One outside for sale Memphis CL. It is in tools...

    One outside for sale Memphis CL. It is in tools by owner.
  24. Replies
    7
    Views
    261

    A513 covers everything from 1008 to 8630 (ref...

    A513 covers everything from 1008 to 8630 (ref Metals & Alloys in the Unified Numbering System)

    Mill scale if present will do more tool damage than the steel will
  25. Replies
    7
    Views
    493

    They just list the weight for 14 X 30, 14 X 54...

    They just list the weight for 14 X 30, 14 X 54 and 14 X 78

    3925, 4325 and 4725 respectively

    Appears to be 400 Lb steps for the additional 2 feet

    Probably be good to assume this was no motor...
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4