Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: friesen

Page 1 of 15 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    6
    Views
    2,399

    I had a similar issue. I ended up putting the...

    I had a similar issue. I ended up putting the old screen back in. My gut feeling was that the video card was slightly off or something, and the screen would lose sync.
  2. Replies
    4
    Views
    429

    Are you inadvertently using dprint? Like using...

    Are you inadvertently using dprint? Like using renishaw reporting for some reason? Just for kicks you could up your rs232 baud and see what that does. For some reason I notice this on haas/renishaw...
  3. Thread: Helicoil taps

    by friesen
    Replies
    11
    Views
    1,068

    Kato tangless definitely better, much easier to...

    Kato tangless definitely better, much easier to install. About taps, I found that helicoil taps from McMaster didn't do so well. The 10-32 completed thread whas about .005" dia too large, and the raw...
  4. Replies
    9
    Views
    2,328

    You are orienting it the same? IE not 180°...

    You are orienting it the same? IE not 180° different.
  5. Replies
    8
    Views
    1,882

    582 and 583 at least for the older controls. They...

    582 and 583 at least for the older controls. They should be within a few tenths.
  6. Replies
    8
    Views
    1,882

    Sounds like it didn't get set up correctly. There...

    Sounds like it didn't get set up correctly. There are two macros in the upper 500 range, one is for spinning tools. You can fiddle with this until it's right if you have a reference.
  7. Maybe consider adding the oil water separator...

    Maybe consider adding the oil water separator thing? Then you can send the coolant back into the tank. Basically everything that you put in the bijur oiler will come out the drain. I think the one I...
  8. Thread: Haas simulator

    by friesen
    Replies
    5
    Views
    855

    Is it nexgen? If not can you just change the xyz...

    Is it nexgen? If not can you just change the xyz travel params?
  9. Replies
    223
    Views
    39,158

    I used to use Alibre and it worked well enough.

    I used to use Alibre and it worked well enough.
  10. Hey, at least the spindle was cushioned.

    Hey, at least the spindle was cushioned.
  11. I dropped my brand new probe onto the way cover...

    I dropped my brand new probe onto the way cover during setup trying to center it, after leaning into the tool release button.. arg.. anyway, it all still worked, but the nose has a ding in it.
  12. Replies
    12
    Views
    1,188

    I went from a diy linuxcnc router to a haas vf2...

    I went from a diy linuxcnc router to a haas vf2 without too much trouble.

    I bought a phase perfect pt330, however I think a rotary would work fine as well. For haas at least, the real point is...
  13. It might be the solenoid. They get old and the...

    It might be the solenoid. They get old and the little internal parts get gummy and quit working.
  14. One thing to watch for is mocon to cpu versions....

    One thing to watch for is mocon to cpu versions. Some versions of mocon paired with older cpu versions mostly work, but rigid tap hangs per my experience, iirc about 9.21 to 12 something.
  15. See macros 582-587 XY 585-586 OTS size 584

    See macros 582-587

    XY 585-586
    OTS size 584
  16. Find the renishaw manual for the exact macros,...

    Find the renishaw manual for the exact macros, but somewhere in the upper 5-600 you'll find the xy for the ots and verify its real position. In my recollection the probe cal doesn't really find...
  17. Replies
    3
    Views
    526

    Or, if you really want pain, edit the macros.

    Or, if you really want pain, edit the macros.
  18. Replies
    3
    Views
    526

    You could find a logic inverter instead,...

    You could find a logic inverter instead, otherwise I don't think the next gen allows you to hurt yourself.
  19. If it still doesn't work, post the complete test...

    If it still doesn't work, post the complete test code, its hard to know with just snippets.
  20. G1Z0F? Maybe it's moving real slow.

    G1Z0F? Maybe it's moving real slow.
  21. Haas has some old docs that explain it. I really...

    Haas has some old docs that explain it. I really think it means this: 1 ms per block means that for example, 100ipm = 100 / 60 / 1000 = .0016", which means the control has that resolution at that...
  22. Blocks per second does not equal lines per...

    Blocks per second does not equal lines per second. There is some sparse documentation on this if you look. The real problem is partly lookahead, which is real low without hsm.
  23. Mine tend to pop on super clean holders that run...

    Mine tend to pop on super clean holders that run 10k about 5 min. Probably because holder starts out cool and warms up, then something makes them wedge, think morse taper wedge effect.
  24. A whiff of the spray lithium grease is all it...

    A whiff of the spray lithium grease is all it takes. I know some say to keep it squeaky clean, whatever, I think long term popping is bad on stuff.

    It is important to have good air supply,...
  25. Replies
    3
    Views
    667

    Well, what's your goal in being able to do this?

    Well, what's your goal in being able to do this?
Results 1 to 25 of 360
Page 1 of 15 1 2 3 4