Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: daryl bane

Page 1 of 60 1 2 3 4

Search: Search took 0.03 seconds; generated 20 minute(s) ago.

  1. Replies
    0
    Views
    137

    Talyvel1 electronic repair questions

    I have an older Talyvel 1, and having indicator issues, fluttering needle, etc. Powering it is not the problem. I decided to replace the capacitors, but having to find exact replacements are almost...
  2. I have not had a chance to find the part# but I...

    I have not had a chance to find the part# but I did see my post in DaveE907 gearbox thread, and I stated the single lipped seals (CR brand) fit the shafts and housings without modification.
  3. I am no help, except I remember the seals were...

    I am no help, except I remember the seals were off the shelf items. I will go and look thru my paperwork and see if anything comes up. I had found coolant had made its way into the gearbox in its...
  4. Check that your lathe is indeed level, and not...

    Check that your lathe is indeed level, and not pointing down somewhere.
  5. Replies
    94
    Views
    4,206

    So I gather that the "quality or manufacture " of...

    So I gather that the "quality or manufacture " of the tool in question is not the issue.. it's the country of origin? Is it inferior in fit and finish to a similar German made item?
  6. There is a time delay tube 6N060 that will allow...

    There is a time delay tube 6N060 that will allow the main contactor to close when it has heated up, specs say usually around 30 seconds. On mine, this is about 5 minutes or more on a chilly morning....
  7. Replies
    11
    Views
    1,287

    I always thought his video production quality was...

    I always thought his video production quality was the best. Anybody that can manage a shop on the side of a mountain in the Italian Alps, must be doing something right.
  8. Thread: Bar runout

    by daryl bane
    Replies
    5
    Views
    500

    I've walked but never ran. Sorry couldn't resist.

    I've walked but never ran. Sorry couldn't resist.
  9. Replies
    6
    Views
    540

    I just bought a Bison D1-6 backplate for my 6"...

    I just bought a Bison D1-6 backplate for my 6" set-tru Bison chuck. It was a on a D1-4 for a lathe that I don't have anymore. As akajun said, you'd have to swap out backplates each time. There is no...
  10. I use PPG products. Deltron is the paint. I...

    I use PPG products. Deltron is the paint. I recently used some Kirker? Brand and it worked just fine. PPG has gotten pretty pricey and I wouldn't blame anybody for finding a substitute, especially...
  11. I use Acrylic Urethane almost exclusively. Tough...

    I use Acrylic Urethane almost exclusively. Tough and beautiful when applied correctly, but...it is imperative that you use a supplied fresh air breathing mask, gloves, etc. The stuff is bad toxic. I...
  12. Replies
    14
    Views
    654

    I had mine rebuilt by Nisonger, they were able to...

    I had mine rebuilt by Nisonger, they were able to restore my dial face, as some numbers were flaking off. The only option other than that(at the time) was to silkscreen a new face. Not cheap. But...
  13. Replies
    19
    Views
    1,083

    I hate to comment cause my memory of this event...

    I hate to comment cause my memory of this event is so far in the past. But I do remember forgetting to install the gasket( due to the excitement at the time), and having to slit it in order to slide...
  14. Replies
    21
    Views
    3,358

    Just got a Morse 14" Metal Devil, for angle and...

    Just got a Morse 14" Metal Devil, for angle and tubing. Seems to work great. Construction and vise is quite good. Get the optional vise jaws.
  15. Replies
    22
    Views
    1,808

    Normally I wouldn't comment, but I think that is...

    Normally I wouldn't comment, but I think that is a machine definitely worth saving. Unless you find something that is a huge deal breaker, it is worthy of a restoration. So many interesting...
  16. Replies
    41
    Views
    4,883

    Nope, nice machine, but I am done.all the bases...

    Nope, nice machine, but I am done.all the bases covered. :) Now just find the time to sit down and do some bits.
  17. Replies
    41
    Views
    4,883

    I have a little, older Christen, nice...

    I have a little, older Christen, nice machine..and a Meteor...and an Optima. But I am insane.
  18. I just got a used Hwacheon from Greer last month....

    I just got a used Hwacheon from Greer last month. Wonderful. I love it.
  19. Replies
    99
    Views
    6,627

    I am having a heck of a time with the photos....

    I am having a heck of a time with the photos. Sorry.
  20. Replies
    99
    Views
    6,627

    I went a looked at some of my old posts, and the...

    I went a looked at some of my old posts, and the original paint color I used was an Alfa Romeo gray. I recently was painting my Monarch tool cabinet and found the 1970's Alfa color was difficult to...
  21. Replies
    99
    Views
    6,627

    Now my '59 was a Navy machine and repainted a...

    Now my '59 was a Navy machine and repainted a million times, but some of the accessories, as listed on the build sheet that were still with the machine were not and still had the original paint. The...
  22. Replies
    18
    Views
    844

    I would suggest removing the table. I sorta don't...

    I would suggest removing the table. I sorta don't know how you could drill and tap the holes without doing it. For mine, it was just manageable smallish slabs of cast iron that I could jig up on my...
  23. Replies
    18
    Views
    844

    319338319337319336Here are some pics of the Y...

    319338319337319336Here are some pics of the Y setup.319335
  24. Replies
    18
    Views
    844

    Well I have to admit I am an idiot. Never drink...

    Well I have to admit I am an idiot. Never drink wine before you make measurements. Both your mill and mine Y travel is the same. Seems I had allowed the width of the scale/reader into the equation...
  25. Replies
    18
    Views
    844

    Mine is a very original UM not a TM like yours,...

    Mine is a very original UM not a TM like yours, universal ,which allows the table to swivel, and to get a useable range close to the spindle, that is most likely the reason for the larger gap. You...
Results 1 to 25 of 1499
Page 1 of 60 1 2 3 4