Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Shawn Ghormley

Page 1 of 47 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    2,271
    Views
    439,300

    Sticky: South Bend 16" serial number 160627, what year is...

    South Bend 16" serial number 160627, what year is this? Thank you.

    262064

    262065
  2. Replies
    24
    Views
    2,541

    I just talked to the seller, the lathe came from...

    I just talked to the seller, the lathe came from the University of Montana maint department but is near Boise, ID now. Lathe is gently used, seller is a gunsmith, 1250 miles one way from Amarillo,...
  3. Replies
    24
    Views
    2,541

    I'm looking at this Bradford 15x30 on CL for...

    I'm looking at this Bradford 15x30 on CL for $3100.

    254938
  4. I'd like to see pictures of the whole lathe, PM...

    I'd like to see pictures of the whole lathe, PM sent.
  5. Sand doesn't help either. 254193

    Sand doesn't help either.

    254193
  6. What about building a rotary phase converter...

    What about building a rotary phase converter yourself, a 15-20 hp idler should be cheap and allow you to run other 3 phase equipment. If you pony start the idler with a small 120v single phase motor...
  7. Replies
    1
    Views
    591

    Help ID this lathe?

    I'm helping try to ID this lathe, it has no tags or numbers that the owner can find.

    253540
  8. Pull off one bell end and remove the rotor, check...

    Pull off one bell end and remove the rotor, check the stator/rotor for a burned spot.
  9. I picked up these two enclosures this week

    Not sure if they are able to be repaired/fixed, WEG is 200 hp and the Hitachi is 50 hp.
    250584
    250585
    250586
    250587
  10. Replies
    9
    Views
    928

    It should run on lower voltage 3 phase power not...

    It should run on lower voltage 3 phase power not sure the 550v will run on 240v but maybe 460v?. I ran a grinder marked 440v on 240v 3 phase.
  11. Replies
    5
    Views
    1,362

    I see this is for sale close to me again, would...

    I see this is for sale close to me again, would this early of a lathe be a poor choice for a first time lathe purchase? Thank you.
  12. Replies
    37
    Views
    3,110

    Hello, you could wire the Phase Perfect into a...

    Hello, you could wire the Phase Perfect into a three phase panel and wire to each machine.I found a used one with breakers.
  13. Most will say to build one yourself, but American...

    Most will say to build one yourself, but American Rotary brand seems popular;

    Phase Converters | Power Transformers | Power Accessories | American Rotary
  14. Replies
    61
    Views
    2,978

    10-4, I'm tracking now on motor selection.The...

    10-4, I'm tracking now on motor selection.The most I've paid for a motor was $100 and it was a 30hp one. Here's a single phase one?

    Lesson 1HP Electric Motor - tools - by owner - sale
  15. Replies
    61
    Views
    2,978

    Re-connectable? You should have huge selection of...

    Re-connectable? You should have huge selection of used three phase motors in Atlanta on Craigslist etc?
  16. Replies
    61
    Views
    2,978

    I have a pile of starters, I'll take a look.

    I have a pile of starters, I'll take a look.
  17. Replies
    61
    Views
    2,978

    Is this the motor?

    Is this the motor?
  18. Try here for info/parts etc. Model Number 311...

    Try here for info/parts etc.

    Model Number 311

    Kellogg American Lubricated Piston Units - Air Compressor Equipment
  19. Thank you sir.

    Thank you sir.
  20. I have a few of the Clausing manuals but they...

    I have a few of the Clausing manuals but they don't have the power feed unit listed as far as oil use.
  21. What oil to use in Clausing 2276 cups?

    I picked up this Clausing 20" drill Saturday, what type of oil should I use in the power feed oil cups. The table looks nice. Thank you
  22. Not sure if the 5hp idler will start the 20hp...

    Not sure if the 5hp idler will start the 20hp idler, but true a three phase machine running will help the load while starting another machine.
  23. Replies
    6
    Views
    1,863

    Made in the USA of US and imported materials.

    Made in the USA of US and imported materials.
  24. Replies
    6
    Views
    1,863

    Mine came in today, not sure how I ended up and...

    Mine came in today, not sure how I ended up and paid for (2)? No biggie, thank you.
  25. I got it, no worries.

    I got it, no worries.
Results 1 to 25 of 1160
Page 1 of 47 1 2 3 4