Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: goooose

Page 1 of 29 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    70
    Views
    9,429

    Notepad++ with the compare add-in...it's free and...

    Notepad++ with the compare add-in...it's free and probably the best text editor out there.
  2. Replies
    5
    Views
    747

    Can you purchase additional offsets? ...sorry,...

    Can you purchase additional offsets?
    ...sorry, didn't read the first thread where this may have been addressed.
  3. No way you're getting 0.2mm of lift due to vise...

    No way you're getting 0.2mm of lift due to vise tightening.
    As mentioned its probably interference between the workpiece edge and the softjaw bottom face/wall transition. Make sure your parts have...
  4. Replies
    70
    Views
    9,429

    Those dogleg rapids will get you every time. Not...

    Those dogleg rapids will get you every time. Not the softwares fault, either setup Mastercam correctly to simulate doglegs or setup your machine to not rapid with doglegs.
  5. Whats the best CAM for drilling a hole? Whats...

    Whats the best CAM for drilling a hole?
    Whats the best CAM for tapping metric threads?

    This forum is turning into a big pile of burning dog shit.
  6. With all this talk of pullstud failure and the...

    With all this talk of pullstud failure and the need for better material to make them from....excuse my metallurgical ignorance...any reason these are not being forged? Is forging not advantageous...
  7. Thread: Tool Numbering

    by goooose
    Replies
    26
    Views
    2,454

    Ya, 100 tools seems to be the max on the 40 taper...

    Ya, 100 tools seems to be the max on the 40 taper machines now, I was looking at the 50 taper machines.

    How would you handle this on the software side?
  8. Thread: Tool Numbering

    by goooose
    Replies
    26
    Views
    2,454

    You assume wrong. Their tool management only...

    You assume wrong. Their tool management only controls the existing 200 offsets, it does not add extras. The horz they make max out at 50 tools, so maybe they don't think you'd ever need more than 50...
  9. Thread: Tool Numbering

    by goooose
    Replies
    26
    Views
    2,454

    Haas has tool management software to allow more...

    Haas has tool management software to allow more than 200 offsets?
  10. Replies
    23
    Views
    3,223

    Very disappointed to hear this. Who are you...

    Very disappointed to hear this. Who are you dealing with at Esprit? I might be able to point you to a more reliable tech...if not, I'll do the demo and Esprit can pay me the commission when you buy!...
  11. A licensing error is completely a different...

    A licensing error is completely a different problem than a VC++ Redistributable problem. Esprit disabling the lock is taking care of any licensing issue you may have had. They are not aware of the...
  12. Why are you blaming them for issues on your...

    Why are you blaming them for issues on your computer?
    Doesn't really sound like you are keeping them in the loop with your problems either. I had a problem updating once, I emailed and had a reply...
  13. What operating system are you running? Are all...

    What operating system are you running? Are all updates applied to it?
  14. Replies
    10
    Views
    1,168

    They have the posts he is looking for. I've used...

    They have the posts he is looking for. I've used it myself. And yes, its open and editable.
  15. Replies
    10
    Views
    1,168

    The 'certified' posts are locked. Pretty sure you...

    The 'certified' posts are locked. Pretty sure you could use one of the base 'open' haas lathe posts and then make any edits you needed.
  16. Replies
    72
    Views
    5,136

    The point about the mlb quiz was the lack of...

    The point about the mlb quiz was the lack of needing an email to get answers. Guess you missed that.

    Were the emails you obtained discarded after sending quiz results? I think not.
  17. Replies
    72
    Views
    5,136

    What does that matter? Lots of websites and...

    What does that matter? Lots of websites and businesses run themselves ethically.

    Example, didn't look far but here's a quiz from mlb.com. Notice no email is required to get the answers, no email...
  18. Replies
    72
    Views
    5,136

    You should be concerned about business practices...

    You should be concerned about business practices like what Bobcad has done here. Think about how often you answer your phone now, shit, even Al just admitted he won't answer his phone due to spam...
  19. Replies
    72
    Views
    5,136

    GDPR (General Data Protection Regulation) is the...

    GDPR (General Data Protection Regulation) is the most important change in data privacy regulation in 20 years. Yes, its EU legislation. I care about it because it's a great first step. Hopefully...
  20. Replies
    72
    Views
    5,136

    Yes, it's unbelievable that your supplied link to...

    Yes, it's unbelievable that your supplied link to your Privacy Policy is a tracked link. Why didn't you just put the url without the tracking? Because, data acquisition....the exact same thing you're...
  21. Replies
    72
    Views
    5,136

    Fucking unbelievable. You start getting up on...

    Fucking unbelievable.

    You start getting up on your high horse, 'We would never do anything shady with your data'....then you proceed to leave a link that tracks where the person came from. Here is...
  22. Thread: Phone Cad App

    by goooose
    Replies
    8
    Views
    1,018

    If your comfortable uploading files to the cloud...

    If your comfortable uploading files to the cloud and really need this ability, OnShape is your best bet. You can access the full design space from any browser, even your phone browser. The app is a...
  23. Replies
    144
    Views
    12,420

    Pretty much any thread that goes beyond 1 page...

    Pretty much any thread that goes beyond 1 page will morph into other topics along the way. And, no, the first post was about how AutoDesks auto update corrupted a file, nothing to do with how to save...
  24. Replies
    72
    Views
    5,136

    ....had to edit. If you don't like how this...

    ....had to edit.

    If you don't like how this group works, why do you come here?
  25. Replies
    144
    Views
    12,420

    Exactly. It's like they are trying to find a...

    Exactly. It's like they are trying to find a problem for their solution.
Results 1 to 25 of 703
Page 1 of 29 1 2 3 4