Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Peter from Holland

Page 1 of 60 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    9
    Views
    366

    Better explanation as I see it If you get wear...

    Better explanation as I see it
    If you get wear in your chain the pitch gets longer on the pulling side of the chain On the slack side it can adapt a bit
    If you look closely at a worn sprocket...
  2. Replies
    9
    Views
    366

    One work around for the sprocket that works sort...

    One work around for the sprocket that works sort of is to rotate them

    Peter
  3. Those seals are there to prevent dirt to enter...

    Those seals are there to prevent dirt to enter the gearbox Not holding the oil in
    So they are orientated the right way IMHO

    Peter
  4. Replies
    9
    Views
    366

    Perhaps the wear is in the chain mostly Metric...

    Perhaps the wear is in the chain mostly
    Metric size chain was very rare in the days the machine was build Even now it is


    Peter
  5. OH and if you have it out do not expect to push...

    OH and if you have it out do not expect to push it in again easy Theslightest tilt will jam it I always line up the head on the machine place the quil on the tableNice and square And then move the...
  6. Replies
    9
    Views
    366

    That is due to wear Wear changes the pitch...

    That is due to wear Wear changes the pitch slightly The chain liesa bit deeper Therefore the nominal diam of the sprocket gets smaller Therefore the pitch gets smaller In addition wear of the chain...
  7. A DRO for EDM has that function I use that on a...

    A DRO for EDM has that function
    I use that on a slotting machine that you can switch off the powerfeed electricaly
    I set the switchpoint at 0 Then toutch the side of the hole with the tool ...
  8. I would buy a cheaper one like a chinese Easson...

    I would buy a cheaper one like a chinese Easson Or a korean Jenix
    Half the price or less as Acurite.Heidenhein or Sony and they function perfectly

    Peter
  9. Always the same question Howmany ??? 10 ...

    Always the same question

    Howmany ???

    10 10000 or 1000000 makes a huge difference

    Peter
  10. They ran at max speed because they were loading...

    They ran at max speed because they were loading the burning coal in the boilers as quick as possible
    Apperently they could not slow down anymore because that would have cost too much coal They...
  11. It had a coal fire in one of the bunkers Started...

    It had a coal fire in one of the bunkers Started in port already
    Right at the place were it collided with the iceberg
    Pictures show a discoloration in port already It was testified that the hull...
  12. 5 Ton is not that big I would start with all...

    5 Ton is not that big
    I would start with all the sheetmetal Unbolt or cut Whatever is convieniant Simultanisly cutting away all wires Keep these apart as that brings more Perhaps salvage the...
  13. MOL logistics perhaps You should know them ...

    MOL logistics perhaps
    You should know them

    Peter
  14. Personnally I would buy one Din 6303 About...

    Personnally I would buy one Din 6303
    About €2,50 or less at Kipp
    I order there on a regular base anyhow
    Not a exact copy but it works and looks good

    Peter
  15. Can you clamp it lenghtwise ?? Works better...

    Can you clamp it lenghtwise ?? Works better probably


    Peter
  16. Perhaps the electromagnetic clutch is bad First...

    Perhaps the electromagnetic clutch is bad
    First check for conductivity
    Then see if it gets the right voltage and if it is AC or DC
    If that is oke perhaps the gap is too big Try to set it...
  17. You should inspect not only the spindle But the...

    You should inspect not only the spindle But the housing where the bearings seat too
    Roundness ecspecially On old machines I never found a housing that was to specs Well At least the few times I...
  18. Do not make them to existing lines then But go...

    Do not make them to existing lines then But go from the first line or a edge

    Peter
  19. Replies
    120
    Views
    88,616

    We do not have 12 fingers though Peter

    We do not have 12 fingers though

    Peter
  20. Yes Looking closer the drawing is completly...

    Yes Looking closer the drawing is completly wrong
    If numbering the triangles clockwise from 1 to 6 starting at 1 0clock
    The triangles 1-3-4-6 need to be recktangles
    No 3 and 4 put together...
  21. Oke How good are you at Dutch :D Symetrical it...

    Oke How good are you at Dutch :D
    Symetrical it is
    Thats my English word for this day then

    Peter
  22. Make it out of 2 pieces Split the drawing in half...

    Make it out of 2 pieces Split the drawing in half That way you have a syncronic model which will form easier and look better
    The 90 dgr bends on the square will be rounded Use a hammer to tap...
  23. Replies
    3
    Views
    344

    Yes Well made machines But that is not unique...

    Yes Well made machines
    But that is not unique to Switserland or Germany

    Peter
  24. Replies
    3
    Views
    344

    They were never made in eighter Switserland or...

    They were never made in eighter Switserland or Germany
    They were imported rebadges Prvomajska ALG 100 made in Zagreb

    Peter
  25. Plain bearings have a lower surface speed as the...

    Plain bearings have a lower surface speed as the balls in a bearing Much lower Deep grove ball bearings that size are in ratio pretty big
    So a plain bearing with even a smaller shaft might do...
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4