Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: BT Fabrication

Page 1 of 22 1 2 3 4

Search: Search took 0.01 seconds.

  1. everything in the plant here 8NM and above has a...

    everything in the plant here 8NM and above has a torque spec. its there for a reason, just some larger fasteners have a much broader torque range they are ok in all defined by an engineer that...
  2. Replies
    32
    Views
    1,417

    20 year old, time to junk it and buy something...

    20 year old, time to junk it and buy something else.
  3. Just in labor adds up, let alone parts costs. an...

    Just in labor adds up, let alone parts costs. an hr here, an hr there and so on adds up fast. expect 10-20 grand easily.
  4. .18 yrd? so like 6 cu ft? gonna spend $200 to...

    .18 yrd? so like 6 cu ft? gonna spend $200 to pour $40 in concrete?
  5. hire someone....

    hire someone....
  6. Replies
    32
    Views
    1,417

    that whole bore will change diameter with all the...

    that whole bore will change diameter with all the welding heat and make it oblong. not a great repair, just V it out and stick it back in. it will most likely break as soon as its mounted back on...
  7. i would be guessing, these aerators are used in...

    i would be guessing, these aerators are used in the beer industry?
  8. Id say to start out, find a local machine shop,...

    Id say to start out, find a local machine shop, lathes of the cnc world start minimum for a decent used one in the 20K+ range and need a few grand more in tooling.

    Most machine shops, like the...
  9. also just found this article about it. ...

    also just found this article about it.

    https://www.texwipe.com/Content/Images/uploaded/documents/Technical-Data/Stainless_Steel_Bleach.pdf



    Part of the article,

    The sodium hypochlorite...
  10. passivization eats the top layer of material...

    passivization eats the top layer of material away, low enough solution that it does take of a few um of material to clean the surface, then washed away within hours it rebuilds the chromium oxide...
  11. Replies
    7
    Views
    490

    Just switch the motor over, much easier and...

    Just switch the motor over, much easier and cheaper on single phase with that low of hp.
  12. it will still happen with 316 also. acid will...

    it will still happen with 316 also. acid will still eat the passivization layer, that is why harsh acids only go in teflon or glass tanks.
  13. it is an oxidiser with an acid salt. Acid eats...

    it is an oxidiser with an acid salt. Acid eats the passivated layer allowing the salt to react to the iron and causing it to rust.

    chemical name is sodium hypochlorite. also not 100% sure but...
  14. need to make the rack that holds tubing not level...

    need to make the rack that holds tubing not level so it goes to the front or back, that way when you have a cut piece, you pick it up and drain it back into the tray
  15. Replies
    16
    Views
    840

    there is the problem, tip radius is 0.016" you...

    there is the problem, tip radius is 0.016" you need a feed larger then that to control chips.

    that is definitely the wrong geometry insert. looks like it is more designed for cast iron and not a...
  16. you will be fine with 30 kva, mine is that to...

    you will be fine with 30 kva, mine is that to step up to 600V and I have a 20 hp rotary on a 100A breaker. 10Hp ran off a 50A breaker single phase no problems.
  17. Replies
    8
    Views
    701

    only experience I have is that it is 100 monel...

    only experience I have is that it is 100 monel more then the other, pretty much sums up my experience with it thusfar.
  18. I wonder if it powers a motor to drive the...

    I wonder if it powers a motor to drive the carrage?
  19. Replies
    7
    Views
    531

    simple, tie into the power supply, put a manual...

    simple, tie into the power supply, put a manual timer, set it on the weekend when you have a project, have timer turn off hour or so after known stop time.
    then during the week you can manually...
  20. Replies
    21
    Views
    1,222

    the bearings dont support anything, even rolling...

    the bearings dont support anything, even rolling load is only 10-20% of total weight. I just used 1" solid all the way through the middle.
  21. Id just sub things like that out to a local shop...

    Id just sub things like that out to a local shop until you need it that bad. or you can burn $ for friends projects, we all know they just want it as cheap as possible because you are there friend.
  22. Replies
    21
    Views
    861

    those pumps will do both 110/220V but will still...

    those pumps will do both 110/220V but will still need the start cap either way
  23. Replies
    28
    Views
    1,402

    that looks more like poor weld prep.... look at...

    that looks more like poor weld prep.... look at all the impurities in it.
  24. Replies
    21
    Views
    1,222

    my 1400 lb roller only uses 1" pillowblock...

    my 1400 lb roller only uses 1" pillowblock bearings
  25. yg1 I can get here in canada no problem. love the...

    yg1 I can get here in canada no problem. love the endmills so far. I really should try that one now.
Results 1 to 25 of 540
Page 1 of 22 1 2 3 4