Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: iwananew10K

Page 1 of 60 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    13
    Views
    655

    yes, contact with the ways where the head...

    yes, contact with the ways where the head sits...they don't have 100% contact but should be touching some everywhere it mates...each end of the flats and each end and both sides of the v's...

    Your...
  2. Replies
    20
    Views
    888

    hmmm, yes, a logistics problem there.:) the...

    hmmm, yes, a logistics problem there.:)

    the factory metric kit was all 16DP so it would all fit.

    There should be no issue with GPs suggestion tho? 24stud to 80idler to 48lead?
  3. Replies
    20
    Views
    888

    As a more than 1 way to skin the kittie, since...

    As a more than 1 way to skin the kittie, since the OP already has the translation in place (80/63) couldnt the 48T also go on the stud position to generate the 1.5?

    And if a 40T gear can be...
  4. Replies
    13
    Views
    655

    I do not think they would do that at the factory....

    I do not think they would do that at the factory.
    I have seen it before, usually from a questionable rebuild where they just "cleaned up" the ways and did not maintain the geometry.
    Also possible...
  5. Replies
    13
    Views
    655

    no harm, no foul.. if it works all good, if not...

    no harm, no foul.. if it works all good, if not then check it out.
  6. Replies
    13
    Views
    655

    OK, this sound like oil got between the bearing...

    OK, this sound like oil got between the bearing shells and the casting...the bearing should be installed dry in the bores,I suspect you are having to torque the expanders to squeeze the oil out.
  7. Replies
    58
    Views
    4,161

    ^^^ for the most part agree with the above. at...

    ^^^ for the most part agree with the above.
    at some point it's like putting racing slicks on a smart car, it not gonna help and may even be harmful as belt slippage can save your butt sometimes, so...
  8. Replies
    58
    Views
    4,161

    cutting grooves and using a wider belt won't help...

    cutting grooves and using a wider belt won't help IME.
    the 1" deflection thing doesn't really apply in your case for a couple reasons.
    shorter belt plus the poly v for all intents has no stretch.
    ...
  9. Replies
    58
    Views
    4,161

    mine was performing TOO well, it would have eaten...

    mine was performing TOO well, it would have eaten itself given the chance.
    I had a bigger lathe and was starting to teach my son how to use the 9",, thus the reason for going back to original.

    so...
  10. Replies
    28
    Views
    1,357

    yes, what Bob said...something is moving that...

    yes, what Bob said...something is moving that shouldn't.

    Stick mag base and indicator on things while running to isolate and narrow it down....just like you would look for a short in...
  11. Replies
    22
    Views
    1,078

    I have resisted,and as sucky as it is,I am...

    I have resisted,and as sucky as it is,I am considering finding out what it's REALLY like to not have Vericut.
  12. Replies
    2
    Views
    384

    no experience but let the dimension to the blade...

    no experience but let the dimension to the blade cutting tip and blade widths be your guide (and the cost/availability)....if you already have the #7 holder you might try one of the retrofit blades...
  13. Replies
    36
    Views
    1,728

    well, it not vintage, but it is small and WAY...

    well, it not vintage, but it is small and WAY better than a milling attachment! it would certainly hold you over.

    Enco Milling Machine 120 Volts - tools - by owner - sale
  14. Replies
    36
    Views
    1,728

    that was a good buy....what part of Florida are...

    that was a good buy....what part of Florida are you? Is weight a factor for the mill?
  15. Replies
    36
    Views
    1,728

    the drill press unit is not a quality item but...

    the drill press unit is not a quality item but may still be ok on a small drill press....it looks like what harbor freight currently sells.

    the milling attachment is a Palmgren, and is terribly...
  16. drill with it, .010" probably will have no effect...

    drill with it, .010" probably will have no effect in operation...drills being what they are.
  17. 2.25" bottom spud would indicate 13"- Verify...

    2.25" bottom spud would indicate 13"-

    Verify other dimensions from this spec sheet-
    http://vintagemachinery.org/pubs/1617/17500.pdf
  18. Replies
    36
    Views
    1,728

    Yes, per above 1948. The site you found is...

    Yes, per above 1948. The site you found is accurate and a treasure trove of info, you just need to realize SB started their numbering system over at least twice...if you keep scrolling down on the...
  19. Replies
    4
    Views
    402

    Look up round nose finishing tool in...

    Look up round nose finishing tool in HTRAL....your tool can work too but angle it so it not digging in....the RN tool will let you get up next to your center too.

    With the RN tool I would be...
  20. Replies
    4
    Views
    402

    With my lantern by far the best results on 01...

    With my lantern by far the best results on 01 were with a round nose tool and pushing the feed a bit.
  21. Hand only....just knocking off burrs or high...

    Hand only....just knocking off burrs or high spots...object it to leave as much original surface as possible....do not use machine power or chuck the reamer in any way!
  22. Replies
    6
    Views
    427

    Excellent! Please don't take my cautions...

    Excellent! Please don't take my cautions personally, I include them only as a generality.
  23. Replies
    6
    Views
    427

    There is no Allen...AFAIK. Pretty sure it's...

    There is no Allen...AFAIK.

    Pretty sure it's like most SBs, that hole in the end off the knob is simply a center drilled hole from manufacturing.

    what holds the knob on is a straight pin that...
  24. guessing it was like this? not hex nuts but...

    guessing it was like this? not hex nuts but handles?

    4140PH round, thread the internal and weld recreation of the handle on.

    blend and done.

    Brown & Sharpe Mfg. Co. - 1894 Image-Brown &...
  25. Replies
    19
    Views
    1,103

    in the words of some dude I never knew... ...

    in the words of some dude I never knew...

    "bummer"
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4