Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Tony Quiring

Page 1 of 60 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    10
    Views
    573

    You stated " BATTERY"... Look for good quality...

    You stated " BATTERY"...

    Look for good quality battery of AGM type that can run everything for a few minutes minimum.

    Meet get a battery charging power supply that will properly FLOAT the...
  2. Replies
    76
    Views
    4,290

    Close... The intent of my suggestion was to be...

    Close...

    The intent of my suggestion was to be able to repeat all motions in a different place.

    By cutting on the back side with carriage movement it is same extension of tooling and similar...
  3. Replies
    52
    Views
    3,841

    OCPH. Operational Cost Per Hour. Add all...

    OCPH.

    Operational Cost Per Hour.

    Add all costs of operating the company except input materials.

    Power, rent, payroll etc.

    Add up total available billable hours, not managers but just...
  4. Replies
    76
    Views
    4,290

    Get a chunk of round same length as your problem...

    Get a chunk of round same length as your problem then with lathe in reverse use suspect tools and cut on the back side of object.

    Same forces involved in slightly different spot.

    Sent from my...
  5. Higher voltage is less current for same power,...

    Higher voltage is less current for same power, simple ohms law math...but the motor resistance is same with increased voltage so we assume higher voltage would mean higher current with same load.
    ...
  6. Replies
    13
    Views
    1,407

    Get a socket that fits it and use an impact gun....

    Get a socket that fits it and use an impact gun.

    Should zip it free fast, just hold the rod and zip it.

    Sent from my SM-G781V using Tapatalk
  7. A solar panel on top or trailer charges the...

    A solar panel on top or trailer charges the battery for GPS.

    Fleet of generators had them.

    Sent from my SM-G781V using Tapatalk
  8. Best SFIC is really good and standard. Youu...

    Best SFIC is really good and standard.

    Youu can get American padlock shackle style that is well built or you can get the hockey buck style.

    Different folks make cores to that standard so you...
  9. Replies
    54
    Views
    4,555

    Stumbled on this one yesterday.328252 Sent...

    Stumbled on this one yesterday.328252

    Sent from my SM-G781V using Tapatalk
  10. Replies
    35
    Views
    3,182

    Mix light oil with solvent about 10 to 1 solvent...

    Mix light oil with solvent about 10 to 1 solvent to oil.

    Spray this on your bare metal and wipe down with clean rag to insure everything coated.

    Solvent evaporates and leaves a thin oil film.
    ...
  11. Greased lightening at Lowes. Get the 5 gallon...

    Greased lightening at Lowes.

    Get the 5 gallon for 26 bucks and use full strength.

    Safe on hands and zero smell.

    Grease and oil melt away fast.

    Rinse with a dawn mix to capture and carry...
  12. Replies
    82
    Views
    7,003

    Back in the day when ma bell did more work in...

    Back in the day when ma bell did more work in business it was funny, really with the 5 button multi-line style where eash phone had a 25 pair cable.

    One guy placed the plywood on the wall.
    ...
  13. Replies
    40
    Views
    2,694

    There is hvac epoxy that is expensive dot very...

    There is hvac epoxy that is expensive dot very strong stuff, used to fix the coils and such.

    Given the bolt in there maybe toss into the mix some ammo for bb gun.

    Put epoxy in first pushing...
  14. Replies
    21
    Views
    1,062

    Is there a material to make the shaft that has...

    Is there a material to make the shaft that has poor heat transfer?

    Depending on heat cycle the shaft may still transfer heat to bearings.

    Smaller diameter maybe?

    Sent from my SM-G781V using...
  15. Replies
    7
    Views
    977

    We may have one. It has been stored upstairs...

    We may have one.

    It has been stored upstairs for maybe 15 years.

    Was working when upgraded.

    It is large hp plotter but not certain of model.

    Located in Central ca.
  16. Use one t and make a separate manifold . This...

    Use one t and make a separate manifold .

    This is our irrigation status panel, manifold inside, it is a solid with ports made as needed. This one is different from op.

    Ours needed to monitor 5...
  17. Replies
    18
    Views
    964

    Can be anything. Needs to be the load plus...

    Can be anything.

    Needs to be the load plus charge.

    You need to determine if the battery just maintains the memory and nothing else then micro amps of load.

    If you can measure this then easy...
  18. Replies
    54
    Views
    4,555

    Chp inspection stations have a creeper that has a...

    Chp inspection stations have a creeper that has a u shaped bracket made of steel strap that has large casters mounted to ends then it drops down close to ground with "bed" supported there.

    Very...
  19. Replies
    23
    Views
    1,592

    What you describe is just basic power supply. ...

    What you describe is just basic power supply.

    Value seems to small for ripple filtering but may be for noise filtering.

    Either way, what matters more is voltage rating, can be higher but not...
  20. If too small to start call for another chunk. ...

    If too small to start call for another chunk.

    Reject the material

    Sent from my SM-G781V using Tapatalk
  21. Replies
    27
    Views
    2,185

    If you can loosen existing bolts then you can try...

    If you can loosen existing bolts then you can try drilling the hub from exposes side and thread bolts in from that side against the flange.

    You need to know how deep to go ro just use to mount a...
  22. Replies
    202
    Views
    12,369

    Another stupid first question... If you had in...

    Another stupid first question...

    If you had in hand a repaired case with it clearly marked as repaired as well as providing document explaining the repair may alter the strength of the case...
  23. Replies
    202
    Views
    12,369

    To the op... Change your process. How about...

    To the op...

    Change your process.

    How about first requesting just ONE task.

    Request quote to scan the good part via whatever process to create a 3d model that you could then use to create...
  24. Replies
    59
    Views
    3,782

    Make it thicker too. More meat in same narrow...

    Make it thicker too.

    More meat in same narrow space

    Sent from my SAMSUNG-SM-G930A using Tapatalk
  25. We modified our 3 layer drum switch. Removed...

    We modified our 3 layer drum switch.

    Removed the cross wires so it now is a 3 conductor, on-off-on switch.

    Using basic 3 wire control with separate pot.

    Bent the contacts on ONE conductor so...
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4