Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: vmkelley

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    3
    Views
    847

    Bosch servo cards Was your machine the 220...

    Bosch servo cards Was your machine the 220 volt or the 140 volt ? It seems like the Z is so heavy that with the lower 140 volt uses a lot of power .Thanks for the reply .This machine was saved...
  2. Replies
    3
    Views
    847

    Deckel servo drive parts

    We would like to buy or repair Bosch Circuit boards 140 volt # 041458 304401 . What should this cost and where . Thanks Mike235377[
  3. Replies
    25
    Views
    4,657

    We always put a magnet it drain plug as a monitor...

    We always put a magnet it drain plug as a monitor for wear . Larger trucks and some air craft use two magnets in the case plug with wires to a light as a chip indicator or failure indicator . Thanks...
  4. Replies
    17
    Views
    2,431

    Answering questions about heating in northern...

    Answering questions about heating in northern Winters . This how I do it . 186243186244186245186246186247 Waste Oil Furnace , I have used this type for 40 years . This is about the 7h in the Third...
  5. Replies
    17
    Views
    2,431

    I understand what your saying and I did complete...

    I understand what your saying and I did complete insulating the shop .We use a waste oil heater that produces up 180 Degree out put and will make that shop 65 to70 in record time even in Michigan...
  6. Replies
    17
    Views
    2,431

    A big thanks to all .

    I would like to post a BIG thank you to all people Past and Present for all the help in saving an old Deckel from the scrap Yard. Your post and info of systems and repairs make it possible . It is...
  7. Replies
    18
    Views
    2,417

    No there were real rubber tires and when they...

    No there were real rubber tires and when they move then a pile of black dust . In latter years there are more synthetic compounds not as bad . Seen them myself in the 1960s .Thanks Mike
  8. Replies
    18
    Views
    2,417

    In large fire depts like Chicago they used to...

    In large fire depts like Chicago they used to inset wood blocks into the cement floors to stop flat spots on tires .Mike thanks
  9. Replies
    9
    Views
    1,550

    Thanks very much for the experience and knowledge...

    Thanks very much for the experience and knowledge , these are complicated by the air motor looks like a radial piston motor and has a reservoir for crank shaft oil and feed the intake with air tool...
  10. Replies
    9
    Views
    1,550

    Thanks for your response but these were used 50...

    Thanks for your response but these were used 50 years ago .C couldn't find anything with cable or even back that far . Thanks Mike
  11. Replies
    9
    Views
    1,550

    Ingersol Rand Hoist

    175004175005 Could any one answer what oil should be used in the air motor end and the gear reduction and load brake Serial # 27077 and size b . Air motor # 80444 .Checking the load Brake?Thanks Mike
  12. Replies
    93
    Views
    77,949

    Sticky: Fp 42 nc

    Last year I got it going in limited use,but kept going on soft ware and drive problems . This year it's been very helpful in making many projects . The size and machine mass is helpful with set ups...
  13. 169036169035169034 Here are some more Pics. Mike

    169036169035169034 Here are some more Pics. Mike
  14. 168922168925[/ATTACH]168924 This one way for a...

    168922168925[/ATTACH]168924 This one way for a wood framed pole building .Mike
  15. 168858 This is a factory built Arm on a heavy...

    168858 This is a factory built Arm on a heavy table with a boat winch added .Good for about 2oo pounds.Very handy but not pretty.Mike
  16. Replies
    11
    Views
    2,654

    We use a formula of 12.999 x the number of...

    We use a formula of 12.999 x the number of threads for 10 threads or less . 10 threads per inch = .129 Double depth .this another tool to use to get close .Also Higby cut the starting edge to keep...
  17. Did a little research Ahrens Fox fire Apparatus...

    Did a little research Ahrens Fox fire Apparatus co. All of Joe Michaels info has very accurate an thanks much .The last fire truck A &F made was in 1977. The rights to the company are owned by HME...
  18. John Did this company change into the Ahrens...

    John Did this company change into the Ahrens Fox Company . Mike
  19. We were taught 50 years ago that all threads 10...

    We were taught 50 years ago that all threads 10 threads per inch or less of an even nunber , the double depth is reached by multiplying 12.999 x the thread = double depth . 10 tpi = .129 .Thanks Mike
  20. Replies
    168
    Views
    46,305

    I sure like your work very nice . One thing I...

    I sure like your work very nice . One thing I learned you may probably all ready know is if you save or buy old good screwdriver handles grind them down to fit carbide inserts for scraping off crud...
  21. Replies
    1
    Views
    3,039

    Will this be cheep electrical energy

    This is a very interesting video on a new way of generating energy .
  22. Replies
    27
    Views
    5,194

    I have burned waste oil for the last forty years,...

    I have burned waste oil for the last forty years, started out with the old pot type now that was messy and not very efficient . About 20 years ago they came out with compressed air Atomization ....
  23. Replies
    12
    Views
    3,066

    Thanks for the memories , Nice pictures . Mike

    Thanks for the memories , Nice pictures . Mike
  24. It all goes by pretty fast enjoy it . Nice...

    It all goes by pretty fast enjoy it . Nice looking bunch . We just marked the big 50 this year, your on the way, Good job . Congrats Mike
  25. Many CNC brake presses when you power up the...

    Many CNC brake presses when you power up the machine will go to the top and the next move is to calibrate the Ram by use a code furnished by manufacture . Mike
Results 1 to 25 of 99
Page 1 of 4 1 2 3 4