Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: agieman

Page 1 of 12 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    3
    Views
    222

    it is set up for serial input. you can use...

    it is set up for serial input. you can use hyperterminal in windows. a web search shows it is available for windows 10. most older versions of windows contain hyperterminal in accessories. you will...
  2. Not a sensor malfunction more of a design issue....

    Not a sensor malfunction more of a design issue. keep wire on it and you should be fine. thank you for the kind words.
  3. Replies
    8
    Views
    1,863

    Welcome back my friend!

    Welcome back my friend!
  4. Replies
    11
    Views
    950

    when I ran Wire machines regularly,I ran a grease...

    when I ran Wire machines regularly,I ran a grease distribution program on Monday mornings just to keep everything lubed up. I had a habit of setting parts up in the same general area and mostly used...
  5. leo, take look at the position of RX1 it is the...

    leo, take look at the position of RX1 it is the pulley above the wire spool that controls the wire spool motor. you dont want to power up the machine with the pulley all the way up. roll the wire...
  6. Replies
    12
    Views
    1,444

    Hi Jay, GF has another machine to remove grown...

    Hi Jay, GF has another machine to remove grown parts from a build plate, the CUT AM500. It's designed from the ground up to serve the additive machining industry. it cuts horizontally, uses wire...
  7. Replies
    2
    Views
    475

    FYI: pressure sensors on charmilles288249 were...

    FYI: pressure sensors on charmilles288249 were used much earlier than the introduction of this machine.that being said this machine does not have a set up like that. most likely the float switch...
  8. Replies
    12
    Views
    1,444

    there was a progress 4 kicking around on Ebay...

    there was a progress 4 kicking around on Ebay with a 28in.Z. it was in Ohio somewhere. might be worth a google search it was short money as i recall.
  9. yes to the encoder cards IMC-06/09 if both have...

    yes to the encoder cards IMC-06/09 if both have three sections. i think it is the DMD for XY that is missing the third section. the DMD's are interchangable but you have to swap the PMO's that are...
  10. the excellence has 2 measuring systems on x and...

    the excellence has 2 measuring systems on x and y.
    system 1 rotary encoder on motor
    system 2 glass scale. check connections between glass scale and IMC board.
  11. Replies
    11
    Views
    2,643

    are you using the same tec file for the different...

    are you using the same tec file for the different thicknesses? are you sure its tec for 1.5 in thick material?
  12. Replies
    14
    Views
    1,292

    Check the PH of the water. It sounds like you...

    Check the PH of the water. It sounds like you have some type of chemical reaction going on.
  13. Replies
    7
    Views
    1,015

    has anyone from service visited the machine or...

    has anyone from service visited the machine or was this diagnosed by phone?
  14. Replies
    22
    Views
    2,464

    As a guy who has fixed hundreds of those Agie...

    As a guy who has fixed hundreds of those Agie machines, i usually planned on 2 full days to redo geometry and that was if i didn't have to work on the Z axis. When it was right it was amazing what...
  15. Replies
    4
    Views
    931

    just my two cents. i have yet to see the agie...

    just my two cents. i have yet to see the agie that cant be fixed. software is hard coded on eproms not any hard drive tec is not on machine and has to be entered manually from a chart. parts are...
  16. does it thread automatically?

    does it thread automatically?
  17. Replies
    7
    Views
    1,337

    here is another vote for hermann Schmidt!

    here is another vote for hermann Schmidt!
  18. Replies
    7
    Views
    1,346

    where is the water coming out of the filters....

    where is the water coming out of the filters. they work from inside out and from bottom to top. as they clog the water level on the side of the filter rises. The pressure usually stays low till the...
  19. Replies
    2
    Views
    725

    A and B are on/off times as I recall. do you have...

    A and B are on/off times as I recall. do you have a manual? shoot me your email.
  20. Replies
    6
    Views
    1,245

    What machine? part material? part thickness?...

    What machine? part material? part thickness? wire? how much error? number of passes?
  21. Replies
    4
    Views
    1,049

    he is duplicating the function. does he have the...

    he is duplicating the function. does he have the X value to be entered at 0.0000. if so, then the center of the wire will be zeroed on the edge of the part and it will automatically comp for the...
  22. Replies
    3
    Views
    871

    hi, send me your pics or call me

    hi, send me your pics or call me
  23. Replies
    6
    Views
    1,618

    did you find anything out about the titan...

    did you find anything out about the titan machines?
  24. Replies
    11
    Views
    1,486

    the 510 generator does need periodic tune ups....

    the 510 generator does need periodic tune ups. How are your cables inspect them and make sure the terminations are good.
  25. Replies
    6
    Views
    1,618

    does your sodick use G92 to set reference at the...

    does your sodick use G92 to set reference at the start of every shape in your program? if so, Drill 20 will use it to create drill points so you only need one program for both wire and drill.
Results 1 to 25 of 296
Page 1 of 12 1 2 3 4