Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Tony Quiring

Page 1 of 60 1 2 3 4

Search: Search took 0.04 seconds.

  1. These machines are sought after units. Check...

    These machines are sought after units.

    Check practical machinist page for info but do not post the add is it may vanish...

    Sent from my SAMSUNG-SM-G930A using Tapatalk
  2. We had a reputation for pranks...best one was...

    We had a reputation for pranks...best one was just stating something like "good luck starting the xXxX today..." with proper tone.

    Certain folks would get concerned and double check things 3 times...
  3. Others have expressed interest, I will pass on...

    Others have expressed interest, I will pass on this today.

    Thanks for holding

    Sent from my SAMSUNG-SM-G930A using Tapatalk
  4. Go ahead! We have a chicom set we hardly ever...

    Go ahead!

    We have a chicom set we hardly ever use, if you have a need then I will pass.

    Sent from my SAMSUNG-SM-G930A using Tapatalk
  5. We are interested, have off shore set we almost...

    We are interested, have off shore set we almost never use but us one would be nice.

    How much shipped to 93636? In 2 boxes as described above?

    If local wants it they can have it...

    Sent from...
  6. Put loose parts in flat rate box and tray in...

    Put loose parts in flat rate box and tray in large box.

    Tray not heavy so should be cheap to ship that way.

    Sent from my SAMSUNG-SM-G930A using Tapatalk
  7. Replies
    27
    Views
    1,450

    There are some epoxies rated for hvac coil...

    There are some epoxies rated for hvac coil repairs, not cheap but good stuff.

    You can collect some powdered steel from your bench grinder and clean it with acetone.

    A magnet can be used to get...
  8. Fix it to not repeat... Sent from my...

    Fix it to not repeat...

    Sent from my SAMSUNG-SM-G930A using Tapatalk
  9. Replies
    28
    Views
    3,054

    The scales have your weight about a mile before...

    The scales have your weight about a mile before the offramp to them.

    There are drive over units on the freeway that weigh the truck, measure the truck axles and a bunch of other magic and the data...
  10. Looks like a lot of the copper is worn away. ...

    Looks like a lot of the copper is worn away.

    There must be a data sheet showing minimum usable diameter or there may be a way of measuring the remaining material.

    The un-worn area can be turned...
  11. This is easy... Silly but works... Get a...

    This is easy...

    Silly but works...

    Get a fishtape and run it through the pipe to the other side.

    Now wrap electrical tape on fishtape and pull until it comes out other side.

    Now add a few...
  12. Replies
    18
    Views
    941

    Solar no help. Power wall maybe. Power...

    Solar no help.

    Power wall maybe.

    Power conditioners have many flavors.

    Last we used was basically a multi-tap transformer that a controller switched windings to step up or down voltage to...
  13. Replies
    30
    Views
    2,430

    If in warranty then ask for a certified...

    If in warranty then ask for a certified inspection report that shows in clear language what the spindle is not covered in warranty and have the specific section of the warranty indicated and included...
  14. A Weller pistol gun will do the trick. Cut tip...

    A Weller pistol gun will do the trick.

    Cut tip shorter for more watts.

    Carefully scrape the area to get to shiny surface then it should "tin" with no fuss.

    Sent from my SAMSUNG-SM-G930A...
  15. 24 and 12 volt are common. You could get one...

    24 and 12 volt are common.

    You could get one of each connect in series and make the 36 volts.

    Sent from my SAMSUNG-SM-G930A using Tapatalk
  16. Given these do not seem to be life supporting...

    Given these do not seem to be life supporting structural then the material should be prepped such that the full weld is still lower than flush.

    Proper V cuts at mating parts with correct wire size...
  17. IT does age out. We have a tub of kester flux...

    IT does age out.

    We have a tub of kester flux that usually fixes it.

    Some of the fresh stuff does not seem to work as well.

    We prefered chemwick (spelling not right) back in the day for cut...
  18. This is always interesting. Changing subject...

    This is always interesting.

    Changing subject to point.

    We are carbon neutral regarding heating home.

    Grow our own trees and cut into firewood to burn

    Maybe minus a couple for chainsaw...
  19. Old 1980 ish 300SD almost got that and sounds and...

    Old 1980 ish 300SD almost got that and sounds and smokes like a kenworth.



    Sent from my SAMSUNG-SM-G930A using Tapatalk
  20. Replies
    5
    Views
    943

    Looks like it could have been either generator or...

    Looks like it could have been either generator or central motor.

    Large pulley on each side lean to possible line shaft connection and what looks like motor connected to it may have been add on.
    ...
  21. Replies
    1
    Views
    686

    OT Odd vehicles along the roadway

    We all see them, creative vehicles people make.

    That lifted 4WD camero or other oddity.

    We have a few we will need to fund from years ago but here is a good one to start...

    I bet there are...
  22. Replies
    13
    Views
    1,092

    Check points and dwell. Tiny bit of crud makes...

    Check points and dwell.

    Tiny bit of crud makes fgor resistance which prevents full charge.

    Dwell wrong same thing.

    Condenser will also cause this.

    Sudden fail could be resistor too.
  23. Replies
    13
    Views
    1,092

    Remove all plugs and reconnect the wires and lay...

    Remove all plugs and reconnect the wires and lay plugs on top of head and crank the starter.

    All should have good spark and this will also allow you to check plugs and vent out the engine.
    ...
  24. Ever do business with a hospital as a client? ...

    Ever do business with a hospital as a client?

    Specifically a religious non-profit in past life, had meeting regarding outdated communications equipment and after about an hour or so m ax by...
  25. Replies
    11
    Views
    915

    Haha has an information service so to speak. ...

    Haha has an information service so to speak.

    No need to identify self but to ask for rules and procedures.

    If needed then need to get PROPER procedure and inspection documents.

    If not...
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4