Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: alphonso

Page 1 of 60 1 2 3 4

Search: Search took 0.05 seconds; generated 16 minute(s) ago.

  1. Replies
    5
    Views
    316

    Finally got the servo motor installed. ON button...

    Finally got the servo motor installed. ON button still seems to be a problem in that I can't show any continuity thru points. Button and switch assemby is Klockner Moeller KI-B (or K1-B, can't...
  2. Replies
    5
    Views
    316

    Gaaaaahhhhh!!!!! Monday ran into Tuesday and now...

    Gaaaaahhhhh!!!!! Monday ran into Tuesday and now the ON button seems to have taken a dump.
  3. They must not like you because I have found that...

    They must not like you because I have found that they are always the best price across the board.
  4. Replies
    5
    Views
    316

    Ah so. I will install the new (correct) servo...

    Ah so. I will install the new (correct) servo motor and see what happens. Hopefully today.
    Servo motor that was in machine has a brake that had been disabled/removed. Correct motor does not have...
  5. Replies
    5
    Views
    316

    0TC 400 Alarm Questions

    Getting 400 alarm on power up. Diagnostic 721.7 = overload either with board or motor. I presume 721 is for Z axis.?? If this correct, then problem is with board as the motor is not connected, in...
  6. 0TC now have a question about RS232

    original post and thread:
    0TC CP9A board question

    This morning, looked closely at wires in DP25 connector in machine. Jiggled them a bit and now get an 086 error = DR is off.

    Searched for...
  7. Go here to get manuals. 8055 will be pretty much...

    Go here to get manuals. 8055 will be pretty much the same as 8050.

    :: FAGOR AUTOMATION ::

    IIRC, bring up whatever setting table and there will be a "save" soft key. Press that and it will ask...
  8. Replies
    77
    Views
    3,772

    I had 15 and 16 year old kids sent to me by the...

    I had 15 and 16 year old kids sent to me by the high school back in '78-'79. Two of them stayed with me for 3 years. Went on to pretty damn good machining jobs, doing things that I would have...
  9. Replies
    22
    Views
    1,376

    Fanuc 16 18 Memory Backup/ Restore Procedures...

    Fanuc 16 18 Memory Backup/ Restore Procedures
  10. Replies
    7
    Views
    790

    May have misspoke about RS232 working. When guys...

    May have misspoke about RS232 working. When guys got here this morning we tried to load parameters. EDIT,PARAM, hold EOB and Input down. LSK flashes, does not change to INPUT. Looking at cable...
  11. Replies
    7
    Views
    790

    Some progress. Got parameters from dealer. ...

    Some progress. Got parameters from dealer. Somewhat surprised that RS232 functions. The parameters he sent are identical to the parameters in the "twin" when I got it. Handloaded the 900...
  12. Your tool change system is really 3 different...

    Your tool change system is really 3 different devices that work together.

    1. Tool magazine

    2, Tool arm (changer)

    3. Spindle.

    Chris 59 is referring to the tool arm. Don't have any...
  13. Replies
    7
    Views
    790

    Initialized control. 911 is gone. Crossing my...

    Initialized control. 911 is gone. Crossing my fingers that dealer can find parameters for this particular machine. Give him a week or so. If not, I will load load parameters for near identical...
  14. Replies
    23
    Views
    1,864

    292697 Damn, that's slick. Why haven't I ever...

    292697

    Damn, that's slick. Why haven't I ever thought of doing that? Going to go make one of those this morning!!
  15. Replies
    7
    Views
    790

    Update: one step forward, 2,3,or more backwards....

    Update: one step forward, 2,3,or more backwards.

    Yes, the cables had been swapped.

    Power up. Spindle motor fan doesn't run. Just as I went to turn hydraulics on, error 911 popped up. ...
  16. Replies
    6
    Views
    394

    No idea how your machine works, but on ours we...

    No idea how your machine works, but on ours we hold the manual tool release button down while cranking the tool arm mechanism(hex on end of motor shaft for a socket wrench) until the tool clears the...
  17. Replies
    7
    Views
    790

    What first caught my attention was the...

    What first caught my attention was the differences in the cables themselves. On near identical machine, the cables with the black sleeves are plugged into the M39/M36 sockets.
    Will trace the cable...
  18. Replies
    7
    Views
    790

    0TC CP9A board question

    Been nearly a year since I looked at this machine. Keep getting alarm on Z servo drive, OC I think.. Interesting that sometimes the green light would also be on.

    Not hooked to power at the...
  19. Thread: Vnmg inserts

    by alphonso
    Replies
    10
    Views
    833

    Damn! You let the cat out of the bag. Long live...

    Damn! You let the cat out of the bag. Long live KC935!!
  20. Thread: Vnmg inserts

    by alphonso
    Replies
    10
    Views
    833

    Zcc-CT and Korloy that Exkenna sells have been...

    Zcc-CT and Korloy that Exkenna sells have been pretty good for me. i get them from Bass Tool in Houston. Prices are in the $5 to $7.50 range.
  21. Replies
    112
    Views
    4,810

    I don't know if it is still happening but about...

    I don't know if it is still happening but about 10 -15 years ago, a lot of Haas casting was done by Lufkin in Texas.
  22. Replies
    342
    Views
    25,143

    Don't know if this is Detroit proper or some...

    Don't know if this is Detroit proper or some other municipality but look at Google Earth of Detroit, the area bounded on north by Nevada,west by Chrysler Freeway, South 6 mile Rd. east by Ryan Rd....
  23. Replies
    112
    Views
    4,810

    Apropos of nothing at all, I remember a large...

    Apropos of nothing at all, I remember a large banner that hung on the wall of Rex Tool Supply in Houston: "Every new machine was built with a used machine."
  24. Replies
    4
    Views
    455

    I think you are going to have to replace the...

    I think you are going to have to replace the cable. Insulation on each wire has melted off and bare wires are touching each other. BTDT Got the T shirt.
  25. I understand what you are saying about machine...

    I understand what you are saying about machine getting lost, but the Fagor has a tool inspection routine that is similar to the GE 1050 that I started on (I really miss that routine. You could move ...
Results 1 to 25 of 1497
Page 1 of 60 1 2 3 4