Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Peter from Holland

Page 1 of 60 1 2 3 4

Search: Search took 0.04 seconds.

  1. Not seen a Deckel anywhere Peter

    Not seen a Deckel anywhere

    Peter
  2. I had a Romi EZpath once The wires from the...

    I had a Romi EZpath once
    The wires from the apron to the controls were solid wires or just a few strand No stranded wire like it should be
    Huge mistake IMHO
    On mine there was a disconnect in...
  3. Replies
    27
    Views
    913

    it seems to be the aerosols in your breath These...

    it seems to be the aerosols in your breath These travel much farther The production of aerosols and the time they can excist s affected by absolute humidity which is affected by the weather again ...
  4. Replies
    51
    Views
    1,981

    A ratio of 20 is deep hole drilling territory ...

    A ratio of 20 is deep hole drilling territory
    how it would perform on the material in question I do not know

    Peter
  5. Replies
    4
    Views
    357

    The horror stories you hear are from the US ...

    The horror stories you hear are from the US
    Completly different story here in Holland And I suppose in Germany too
    Very competent people Especialy those driving a boom truck
    BTW I would hire a...
  6. Replies
    27
    Views
    913

    AFAIK it is not that much UV as the microdroplets...

    AFAIK it is not that much UV as the microdroplets of vapour with which the virus travels
    It seems to depend on the absolute humidity
    I wonder how it goes in the northern countries where it...
  7. Replies
    27
    Views
    913

    Over here they start a test at several PCR...

    Over here they start a test at several PCR testlocations
    You first blow in the breathanalizer If that is negative you are done If you test positive on the breathanalizer you do the PCR test witch...
  8. Replies
    27
    Views
    913

    It takes time to train miljoens of dogs We are...

    It takes time to train miljoens of dogs
    We are better in producing as training
    This is a good start
    https://en.wikipedia.org/wiki/Coronavirus_breathalyzer

    Peter
  9. Replies
    27
    Views
    913

    OT Covid 19 breath analizers

    I am not convinced the vaccins will solve the covid 19 pandemic Only partly probably But if the virus keeps mutating we will keep chasing our tail
    Here we start using breath analizers to...
  10. Its been too long I cannot remember (I know...

    Its been too long I cannot remember (I know getting old) But did you check Hawe.com All kind of information available
    I can check monday if I have a old one lying around

    Peter
  11. I use a diamant cup wheel with a wide face for...

    I use a diamant cup wheel with a wide face for things like that
    Works great
    Peter
  12. Post a picture of your valve I have some Hawe...

    Post a picture of your valve
    I have some Hawe valves

    Peter
  13. Perhaps post a picture of the scale and the...

    Perhaps post a picture of the scale and the connector in a assembled state and some dimensions
    Its a 7 pin and most have only 6 pins Thats a recognizable feature
    Someone might recognize them
    ...
  14. Look it up Downloads – SKC Gleittechnik...

    Look it up
    Downloads – SKC Gleittechnik

    Peter
  15. Replies
    15
    Views
    1,080

    Did you search Ricardo ? Peter

    Did you search Ricardo ?

    Peter
  16. Replies
    4
    Views
    357

    Plans for the machine you can download from that...

    Plans for the machine you can download from that french site full of manuals
    TOS SV18 R & RA
    I found no lifting instructions though
    I would see if a sling around the left side over the chiptray...
  17. I would use the SKC compound mentioned in my...

    I would use the SKC compound mentioned in my post 190 or equivalent
    It is more durable as soft solder and no heat involved

    Peter
  18. Replies
    15
    Views
    1,080

    Take along a big bag of money for these...

    Take along a big bag of money for these accessories then :D

    Peter
  19. Corn cob face mill as big as your lowest...

    Corn cob face mill as big as your lowest speedsetting alows
    Ideal would be the wide of the slot
    2 passes to get to depth with feed that does not stop the motor or damage the mill Low then
    Slow...
  20. Replies
    47
    Views
    2,856

    That shear has a lott to endure then :D Peter

    That shear has a lott to endure then :D

    Peter
  21. Replies
    47
    Views
    2,856

    Papershear then Peter

    Papershear then

    Peter
  22. Replies
    15
    Views
    1,080

    I know these french fuses 10X32MM isn't it They...

    I know these french fuses 10X32MM isn't it They cost aarm and leg over here The ones in the picture just peanuts
    Peter
  23. Before using it I would get those galled places...

    Before using it I would get those galled places smoothend Make sure all somewhat loose particals are removed
    But its a perfect candidate for SKC 63R A slideway compound for repairs, I have used it...
  24. Replies
    47
    Views
    2,856

    Not when it matters That is while cutting Then...

    Not when it matters That is while cutting Then the 2 pieces are still one piece (Does that makes sence:D)But anyhow the gap setting is still the same percentage
    One can check the cutting edge 1/3...
  25. Replies
    9
    Views
    708

    I have the German manual in PDF Send me a PM...

    I have the German manual in PDF
    Send me a PM with your e-mailadres and you get a wetransfer link from me

    Peter
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4