Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: michiganbuck

Page 1 of 60 1 2 3 4

Search: Search took 0.08 seconds.

  1. except I did not see the address.

    except I did not see the address.
  2. Replies
    19
    Views
    1,201

    4 jaw chuck is very handy, and a steady rest,...

    4 jaw chuck is very handy, and a steady rest, good to practice/master threading and have a fish and thread gauge and a three wire set,learn how to go quickly from in-the-chuck to between-centers as...
  3. Replies
    158
    Views
    5,757

    Likely with the Earth diameter getting smaller...

    Likely with the Earth diameter getting smaller going away from the equator is why Ontario Canada gas is about $5.00 a gallon compared to about $2.40- $2.50 (Regular) in the USA.

    US Average Gas...
  4. Replies
    158
    Views
    5,757

    Qt:{If what I think is correct would the Earth's...

    Qt:{If what I think is correct would the Earth's rotational speed (24 hours in 1 day) eventually increase, decrease or remain the same?}

    likely it will seem longer.

    and if one is north of are...
  5. Replies
    158
    Views
    5,757

    Guess we need world population control, Just keep...

    Guess we need world population control, Just keep the royals and enough servants for their needs and pleasures.
    Government Population Control: A Secret of American Foreign Policy
  6. Good find Jake..be careful you don't break...

    Good find Jake..be careful you don't break anything and it should last for a good long time. Not a bad idea to hand pull a spindle turn to be sure you have the levers/back gear right so not breaking...
  7. Replies
    158
    Views
    5,757

    QT:{we can use the remainder to grow dope to...

    QT:{we can use the remainder to grow dope to support the every-burgeoning populace of dope-smoking hipsters riding bicycles and powering their Iphones off of the sun.}
    We should mandate roof-top...
  8. Replies
    158
    Views
    5,757

    QT: [IMO this crap doesn't belong here....

    QT: [IMO this crap doesn't belong here. Machining, manufacturing, showing off your new tools,]
    Still machining and environment may be/is abut having and not having manufacturing in one's country....
  9. Replies
    158
    Views
    5,757

    Climate change was proved by the ice ages..likely...

    Climate change was proved by the ice ages..likely dinosaurs fart cause the Ice Ages (not)..Still we should try to protect the world and the USA is doing that very well...Airplane fuel dumping is a...
  10. A jig bore reamer has a very stout shank so the...

    A jig bore reamer has a very stout shank so the spindle bore is better followed. They need a stout machine to provide location/spot and a little dewell at the entering is good. IMHO
  11. Replies
    28
    Views
    1,193

    I caught that Bloomer about running a lathe but...

    I caught that Bloomer about running a lathe but the news but the news did not make a big deal..just as tough as farming IMHO.
    *To the OP an apprentice is very good, trade school in Germany likely...
  12. A drill with a pre-drill (smaller) hole will cut...

    A drill with a pre-drill (smaller) hole will cut to the micrometer check size of the last drill ( + a few tenths).. just drilling a hole with not a pre-drill it may cut oversize. A drill with a point...
  13. Replies
    12
    Views
    1,171

    All the above and also try brand new Wheel..at...

    All the above and also try brand new Wheel..at least a different one and with it fresh dressed..First. It's not uncommon for a wheel to to be coolant logged on one side so no amount of dressing can...
  14. Replies
    93
    Views
    4,358

    My friend Jim Mick wrote a book about his...

    My friend Jim Mick wrote a book about his travels.
    It might be interesting or you to read.
    High on a Wing: A Motorcyclist's Travel Log to, and Trivia About, Highpoints | Highpointers Club
  15. Replies
    21
    Views
    1,877

    Qt:[machine shakes violently] can lead to broken...

    Qt:[machine shakes violently] can lead to broken cutters..

    Many speed and feed recommendations are for the very best conditions like best fixturing and heavy solid parts...
  16. A bubdy heater will run 6 hours set at low.. dont...

    A bubdy heater will run 6 hours set at low.. dont know how safe that might be.
  17. Still it is difficult directing the building of a...

    Still it is difficult directing the building of a turbo encabulator with the hobby machinist only having a budget China lathe and never reading the book How to Run a Lathe .
    Perhaps running the...
  18. Replies
    14
    Views
    1,212

    QT: [Can anyone provide a rational for such an...

    QT: [Can anyone provide a rational for such an odd angle? I am at a loss.]
    It is hard to rationalize machine tapers when one looks at Morse and Brown and Sharpe with many only a few thousandth or...
  19. Replies
    4
    Views
    475

    Knocking on doors works. Craigslist might work...

    Knocking on doors works. Craigslist might work but likely doing more answering questions than getting jobs.
    agree here may work.
  20. Replies
    28
    Views
    1,988

    Chuck can have rotational error and a simple run...

    Chuck can have rotational error and a simple run an indicator there while hand turning the part will tell what that is.
    A 4 jaw chuck can be adjusted to near zero but if it is a poor chuck can have...
  21. A running for test heavy 10 with taper attachment...

    A running for test heavy 10 with taper attachment for 800 seems a deal..
    likely gone already..... Darn.
  22. Replies
    28
    Views
    1,988

    Starting place is check to see the head and tail...

    Starting place is check to see the head and tail center line is the same, check horizontal and vertical. 10 minuets.

    Be sure the live tail center is true running true .001/,0002 or better.. 5...
  23. Replies
    28
    Views
    1,988

    QT:[ far- end by the live center turns .009”...

    QT:[ far- end by the live center turns .009” smaller]
    *I would never turn a 30" part to find the lathe error.
    One can run an indicator on a live center. (do that and report back to PM)
    One can...
  24. Replies
    20
    Views
    2,299

    Is it just the trigger problem, or is the bolt...

    Is it just the trigger problem, or is the bolt physically lose? (yes, if a bolt action or what). Does it close on a bullet and to locks secure or is that where it is loose. *Has a gun smith looked at...
  25. Replies
    10
    Views
    904

    Guess you are right Trev I have made chamber...

    Guess you are right Trev
    I have made chamber reamers and other reamers by all the methods I mentioned.
    Keep it simple is likely the best teaching...Your post #3 does that.
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4