Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Blazemaster

Page 1 of 27 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    21
    Views
    1,223

    I recently bought a machine from a dealer sight...

    I recently bought a machine from a dealer sight unseen. They had it up for a decent price but said it could not be plugged in to power up. They assured me it worked before it was unplugged. I had...
  2. Replies
    10
    Views
    611

    I have a Beebe Bros 3 ton hoist that looks very...

    I have a Beebe Bros 3 ton hoist that looks very similar to the coffing LSB. I have used it for all kinds of stuff from pulling to lifting to clamping. If I had the choice, this is the type of chain...
  3. Replies
    82
    Views
    8,272

    I have a diesel 93' super duty (f450) with 12'x8'...

    I have a diesel 93' super duty (f450) with 12'x8' flatbed, air ride, telma retarder, banks turbo. It does pretty well but it's a little slow and there are times when I need a little bigger truck....
  4. Replies
    9
    Views
    1,065

    Looks like most of the parts are there, and some...

    Looks like most of the parts are there, and some nice extras. I also see some broken handles and by the looks of it they treated it like scrap when it was moved, also sitting in the rain. If people...
  5. Replies
    9
    Views
    1,072

    Yes. Spindle lever would not engage, and the oil...

    Yes. Spindle lever would not engage, and the oil was not flowing through the sight glass for the spindle/column. I still haven't had a minute to look at it closer.
  6. Replies
    9
    Views
    1,072

    Thanks for the replies. I am going to make...

    Thanks for the replies. I am going to make another go at it today, I was getting frustrated yesterday. I don't think it was the clutch but I will check it, and all the feeds/rapids worked. It's not...
  7. Replies
    9
    Views
    1,072

    Here are some pics 280688280689280690280691

    Here are some pics

    280688280689280690280691
  8. Replies
    9
    Views
    1,072

    K&T 2k column problems

    I have an old 2k that I could use for a job and it quit workin on me. Went to start it up one day and it wouldn't quite engage when you pulled the lever, felt like it was catching on something. I...
  9. Shizouka doesn't seem to be too hot of a topic on...

    Shizouka doesn't seem to be too hot of a topic on the forums and most of the threads I have seen are on the AN-S
  10. Replies
    20
    Views
    1,776

    You can drive taps with those Scully Jones split...

    You can drive taps with those Scully Jones split sleeve drivers, can find em on ebay cheap sometimes. Can also make something out of an old mt4 tool that gets no use/broken. Just drill a hole for the...
  11. Replies
    3
    Views
    678

    Well that didn't take long. Had about 30 calls...

    Well that didn't take long. Had about 30 calls since last night. Sold.
  12. Replies
    3
    Views
    678

    Here are some pics, hope they dont come out...

    Here are some pics, hope they dont come out upside down

    279876279877
  13. Replies
    3
    Views
    678

    Towmotor lt-35 1 ton forklift

    I have a 60's towmotor lt-35 forklift. It is rated to lift a ton, and goes 12 feet high. Propane powered, has been a good little starter lift for me. I picked up a larger lift, so this one has just...
  14. Replies
    13
    Views
    1,691

    Threw in a new coil and condenser today and it...

    Threw in a new coil and condenser today and it fired right up. Anyone wanna buy a tiny 1 ton lift?
  15. Replies
    13
    Views
    1,691

    Well I checked timing and that seems to be fine....

    Well I checked timing and that seems to be fine. At this point I am thinking it is a weak spark. Although it is blue, it doesn't seem to want to jump any type of gap.
  16. I'm not so sure I would have handled it...

    I'm not so sure I would have handled it differently. Pissed me off just reading it lol. Some people have no respect and can't take a hint.
  17. Replies
    13
    Views
    1,691

    Thanks for the replies. I will go ahead and check...

    Thanks for the replies. I will go ahead and check the timing tomorrow and verify spark again. I am smelling a little propane on startup, but it's because I have been holding the purge button open...
  18. Replies
    13
    Views
    1,691

    I put new plugs in it about 6 months ago when i...

    I put new plugs in it about 6 months ago when i did a tuneup. I will check the distrib key but I don't think that's it. Thanks
  19. Replies
    13
    Views
    1,691

    Forklift won't Start

    Here's a little back story. I recently picked up a new forklift and I have been getting ready to sell my old one. I've had the new one for a few months. I warmed up the old one and used it to change...
  20. Replies
    16
    Views
    1,440

    I have a wallace 15 ft span, 13ft tall, 3 ton...

    I have a wallace 15 ft span, 13ft tall, 3 ton crane that uses an s10x25.4. I have used it to load and unload lots of machines in the 3-6000lb range. I would imagine a s7x15.3 would be fine for...
  21. You are mistaking the word "better" for...

    You are mistaking the word "better" for "profitable".
  22. I love when people try to convince you to sell...

    I love when people try to convince you to sell off YOUR stuff for THEIR reasons. I'm guessing with 1000 horizontal cutters you won't know what you have until you store them properly, which is what...
  23. Replies
    4
    Views
    721

    Sure there are other machines that would make...

    Sure there are other machines that would make quicker work of it but if an M head is what you have and the part is within its travels it should be able to do that, just will take a bit longer.
  24. Replies
    38
    Views
    2,263

    I have a friend that is a butcher and he gave me...

    I have a friend that is a butcher and he gave me a stack of old butcher coats. They are white so they get dirty pretty easy but that's what they are there for
  25. Replies
    4
    Views
    623

    Well after fussing with it for an hour or so I...

    Well after fussing with it for an hour or so I finally figured it out. The manual makes it sound so simple but when they say move the table leftwards until you can see the threaded rings, you need a...
Results 1 to 25 of 667
Page 1 of 27 1 2 3 4