Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: HWElecRepair

Page 1 of 30 1 2 3 4

Search: Search took 0.02 seconds.

  1. Most DRO manuals want a longer-is-better standard...

    Most DRO manuals want a longer-is-better standard for linear error comp. I use a 14 and 18 inch standard for X and 123 block for Y when I do it. The longer standard you get for linear error comp,...
  2. The wear on the ways isnt all too bad. Still...

    The wear on the ways isnt all too bad. Still some flaking near the dovetail.


    Jon
  3. Replies
    3
    Views
    246

    Rah ANG +1 to what Gbent said. The circuit...

    Rah ANG

    +1 to what Gbent said. The circuit board is probably the issue if both the XY and Z are doing it. The KBMM125 should be the replacement, unless its a British one. But now that I say...
  4. Does this pop up before the beeps? My guess is a...

    Does this pop up before the beeps? My guess is a corrupt software/hard drive. Could also be the motherboard.

    If you have the boot disk in and it isnt booting from that from the get go, then my...
  5. I need to make friends with your friends. :D ...

    I need to make friends with your friends. :D Those are steals.

    Jon
  6. Not arguing it, but I can count on one hand the...

    Not arguing it, but I can count on one hand the amount of times a seller didnt say it saw little use and had great ways :D

    If you can get a J head for a good price and the ways are in the...
  7. Replies
    25
    Views
    1,752

    @thermite is an officer? go freaking figure. It...

    @thermite is an officer? go freaking figure. It all makes so much sense now. lmao

    I hope you all are celebrating safe today.

    Jon
  8. Replies
    4
    Views
    318

    It is near impossible to say if a machine is...

    It is near impossible to say if a machine is worth the cost without seeing it. $4k for a solid Lagun is a fair price.

    Just know that Lagun is VERY proud of their parts, and you will have to put...
  9. Replies
    25
    Views
    1,752

    Rah. 6467/8411 2002-2011 Jon

    Rah. 6467/8411 2002-2011

    Jon
  10. Replies
    8
    Views
    466

    Ya we don't mess with 50s, 70s, or 90s. ...

    Ya we don't mess with 50s, 70s, or 90s. Hopefully they can help you out.

    Jon
  11. Safe? Sure. The longer you run it with worn...

    Safe? Sure. The longer you run it with worn stuff, it will eventually wear more solid and more expensive parts.

    But safe, ya.

    Jon
  12. Replies
    4
    Views
    383

    No, There are two short cables that criss cross...

    No, There are two short cables that criss cross from the motherboard to the interface board. The front connector underneath the motherboard is your VGA connector. Plug directly in there.

    Jon
  13. Replies
    4
    Views
    383

    Yup, just plug it directly into the motherboard. ...

    Yup, just plug it directly into the motherboard. I forget which connector it goes into, there are two very similar plugs in a cross cross patter under the computer int he cabinet.

    Jon
  14. Without seeing the inside of the ger box, this...

    Without seeing the inside of the ger box, this sounds like its a similar issue, or the teeth on the two gears are wearing.

    Jon
  15. Dang, had my entire comment typed out and then...

    Dang, had my entire comment typed out and then had a database timeout, freaking PM.

    Dont think of that spring as being what pushes the driven clutch into the gear. That is a tiny spring and is...
  16. Ya, you can get the powerfeeds for the X Y and Z....

    Ya, you can get the powerfeeds for the X Y and Z. I would recommend definitely going with the 200 on the knee for that beast.

    Jon
  17. I am 99% sure that the Interact didnt come as a...

    I am 99% sure that the Interact didnt come as a manual machine. With that being said, turning it to manual will be completely modified by you to make it work. I have seen centroid retrofit kits on...
  18. Series 2s can come with 6F/8F powerfeeds on them,...

    Series 2s can come with 6F/8F powerfeeds on them, and I know you can put Servo's on the knee. I would have to look to see if they have a kit for the XY, which I think they do.

    Jon
  19. Replies
    7
    Views
    579

    I had to learn it the hard way. :D Jon

    I had to learn it the hard way. :D

    Jon
  20. Replies
    7
    Views
    579

    When you check for accuracy of movement, first...

    When you check for accuracy of movement, first check a shorter movement via indicating off the actual reader head. That will show the most true movement. If you check off the quill, there are many...
  21. The spring behind the gear isn't necessarily...

    The spring behind the gear isn't necessarily there to engage the gear. If it isn't engaging properly when you put it in gear, my guess is that your switches have some oil in it and are sticking. As...
  22. Replies
    7
    Views
    579

    If it reads everywhere except the ends right out...

    If it reads everywhere except the ends right out of the box, then the two main reasons for this would be manufacturers defect or misalignment. if it reads everywhere but the ends, it is a good...
  23. Replies
    18
    Views
    9,339

    We sell a kit...

    We sell a kit that comes with everything you need to go from zerks to a bijur lube system.

    Jon
  24. Replies
    2
    Views
    590

    Better information would help people want to...

    Better information would help people want to respond. The info given doesn't help offer any advice.

    What exactly is happening?

    Jon
  25. Replies
    17
    Views
    2,563

    Just to clarify, the X axis of the scale does not...

    Just to clarify, the X axis of the scale does not work? Or X axis of the box? And when you swapped the connectors, which part still failed?

    Jon
Results 1 to 25 of 745
Page 1 of 30 1 2 3 4