Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Rob F.

Page 1 of 60 1 2 3 4

Search: Search took 0.06 seconds.

  1. Replies
    33
    Views
    880

    I have been thinking of making a new trailer with...

    I have been thinking of making a new trailer with similar set up for brakes.
    Here are a few:
    Electric Over Hydraulic Trailer Brake Actuators
  2. That dude seems to embraced the lifestyle of the...

    That dude seems to embraced the lifestyle of the movie Quest for Fire.
    No talking in the entire movie.
    Here it is in another language, but remember No Talking in it so...:

    YouTube
    ...
  3. If no replacement parts can be found it could...

    If no replacement parts can be found it could easily be used for wood turning and/or metal spinning.
  4. Replies
    38
    Views
    1,396

    Yes, Type L or K, avoid M, it is the thinnest.I...

    Yes, Type L or K, avoid M, it is the thinnest.I think some of the sharkbite type fittings are removeable/reuseable. Never used them though.
  5. Replies
    38
    Views
    1,396

    Here is the one I was thinking of:...

    Here is the one I was thinking of:
    https://www.practicalmachinist.com/vb/general/air-line-question-371639/?highlight=pvc+shrapnel

    I personally knew a guy (best friends brother in law) who ran a...
  6. Replies
    38
    Views
    1,396

    Did you read the air line thread recently posted?...

    Did you read the air line thread recently posted?
    Stay away from the PVC.
  7. Replies
    38
    Views
    1,396

    Cant you get a single phase motor for the same or...

    Cant you get a single phase motor for the same or less money?
  8. Thread: Mystery Monarch

    by Rob F.
    Replies
    15
    Views
    1,738

    You know this thread is from 2006?

    You know this thread is from 2006?
  9. Replies
    18
    Views
    550

    I was mistaken about the smooth chrome, fuzzy...

    I was mistaken about the smooth chrome, fuzzy memory of something else I guess...
    This vid might help you, it shows a clear pic of the chrome ways:
    YouTube
  10. Replies
    18
    Views
    550

    OK my mistake.

    OK my mistake.
  11. Replies
    18
    Views
    550

    Deleted, wrong info in post.

    Deleted, wrong info in post.
  12. PM sent on smaller hammers.

    PM sent on smaller hammers.
  13. Even better: The dump bin has the bag attached...

    Even better: The dump bin has the bag attached with your clamp on its output chute as the bin is filling. The bin is on a spring loaded table so when it reaches the proper weight it dumps. This way...
  14. I want to fill the bin, and spend 3 seconds...

    I want to fill the bin, and spend 3 seconds dumping in into the bag. It sounds like you want to clamp the bag to the machine where I want the dump bin. Then feed the machine to fill the bag?
  15. My family has had a brick making factory they set...

    My family has had a brick making factory they set up around 1870 and ran until about 30 yrs ago. Now it is just sitting, yes I am familiar with clay, and its dust.;)
  16. I added a little to first post. I see it as...

    I added a little to first post.
    I see it as faster for the operator to not to mess around with clamps.
    I guess you could put a table under the bag and just bungee the bag to the output. What...
  17. Can you make a dump bin that will go where you...

    Can you make a dump bin that will go where you want to put the sack? The bin would hold 1 sack full and the operator would just hold the sack to the bins chute and tip it to fill, never letting go of...
  18. Replies
    38
    Views
    1,396

    Have you looked into this one I linked to yet?...

    Have you looked into this one I linked to yet? Seems like the perfect size for you.

    It WILL be gone shortly, if not already:...
  19. Replies
    23
    Views
    1,150

    I was being sarcastic. ;) One of the first...

    I was being sarcastic. ;)
    One of the first things I did when I got this house was to change out the junk zinsco panel. I have no love for that crap. Recently I needed a new main (meter) panel and I...
  20. Replies
    38
    Views
    1,396

    This one I saw is 11 hp instead of 20 hp like the...

    This one I saw is 11 hp instead of 20 hp like the SK26, price looks good on it. Have to factor in shipping costs.
    Procyon Machine
  21. Replies
    23
    Views
    1,150

    With the high price of zinsco breakers doent that...

    With the high price of zinsco breakers doent that mean they are better?:sulk:
  22. I hate to recomend ebay but... they do seem to...

    I hate to recomend ebay but... they do seem to have a large audience. Relist all items as auctions with opening bid of double scrap value + ebay fees, let the bidding begin? Can you or ebay send sale...
  23. Replies
    38
    Views
    1,396

    One of these?...

    One of these?
    https://www.practicalmachinist.com/vb/general/eastwood-qst-30-60-air-compressor-371397/?highlight=eastwood+scroll
    It might not be large enough, you dont say what your needs are.
  24. Replies
    23
    Views
    1,150

    To feed a subpanel you can use a "feed lug" or...

    To feed a subpanel you can use a "feed lug" or "pass through" is another name for them. They are just a lug that plugs in like a circuit breaker, but low enough to stay under the metal knock outs,...
  25. Replies
    46
    Views
    10,385

    Seems like anyone near to BC should be going to...

    Seems like anyone near to BC should be going to visit and start making reasonable offers. I would "guess" that any machine tools would come with any and all tooling and accessories for them?
    Agree...
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4