Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Bruce Griffing

Page 1 of 60 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    20
    Views
    1,977

    I would use wood. Lining may not be necessary. ...

    I would use wood. Lining may not be necessary. Baltic birch ply would be my specific choice.
  2. The Haimer has 18kW?

    The Haimer has 18kW?
  3. If you are into DIY electronics, this plus a...

    If you are into DIY electronics, this plus a beefy power supply would probably work well......

    US 1800W ZVS Induction Heating Board Module Flyback Driver Heater+Tesla Coil+Fan 6212809267025 | eBay
  4. I would avoid square corner inserts. Get...

    I would avoid square corner inserts. Get something that takes SEHT or the like.
  5. Replies
    17
    Views
    1,907

    I think delrin would be easier than nylon.

    I think delrin would be easier than nylon.
  6. I would assume all three ball screws are bad if...

    I would assume all three ball screws are bad if it were me. kinda wonder about the linear guides....
  7. Does that machine have the control that Haas no...

    Does that machine have the control that Haas no longer supports? (supports with a complete replacement, but no parts)
  8. That makes sense as the international line is all...

    That makes sense as the international line is all I can find.
  9. I think more patterns are being made by cnc and...

    I think more patterns are being made by cnc and by 3D printing. I also think that parts that were cast in the past are often molded using composite materials now. The lighter weight is very useful...
  10. I can't get any of the links on that site,....

    I can't get any of the links on that site,. except the 2018 catalog, to work. Further, I can't find anyone with General inventory to sell.
  11. Canadian General Tool and Exaktor gone?

    I was looking for a couple of Canadian products. It seems from my search that General table saws and Exaktor sliding tables have bitten the dust. Is this true?
  12. I have had a Minimax since about 1984. Works...

    I have had a Minimax since about 1984. Works fine, but now and then I wish for longer jointer tables.
  13. OT - Need to ventilate an attic with hip roof - powered roof vent?

    Title says it - should I install a powered roof vent or is there another approach? If so - any quality products?
  14. Replies
    15
    Views
    1,104

    Soft Solder is a good choice in some...

    Soft Solder is a good choice in some circumstances.....
  15. Replies
    4
    Views
    402

    OK - I don't know how I missed that. Thanks.

    OK - I don't know how I missed that. Thanks.
  16. Replies
    4
    Views
    402

    Thanks for the link, but sadly this manual is...

    Thanks for the link, but sadly this manual is like mine - no specific instructions; just change interval and size of oil charge.
  17. Replies
    4
    Views
    402

    Kaeser SX Oil change procedure

    I want to start doing my own oil changes on my Kaeser SX compressor. I have the oil change hose that appears to connect to a low spot for draining the oil and a high spot for filling. There is a...
  18. Replies
    25
    Views
    4,220

    Squareness was very easy. I have a pair of 24"...

    Squareness was very easy. I have a pair of 24" vernier calipers. I just laid out a program for a 24" diagonal square with 1/4" holes at each corner. I drilled holes at those points in a test...
  19. Replies
    25
    Views
    4,220

    I have not looked at the router market so I have...

    I have not looked at the router market so I have nothing to contribute there. Further, my router is not what you want, OTOH it may provide some useful information for your search. My router uses...
  20. Need to build a 4' outdoor cabinet for a sink. Materials?

    I need to build a cabinet for a sink on our covered porch. Over a tile floor about 20' back from the edge of the roof. But always open to weather here in Texas. What materials to use? How to...
  21. Dunno what you want exactly, but imported dental...

    Dunno what you want exactly, but imported dental drills are pretty reasonable on ebay.
  22. Replies
    38
    Views
    1,878

    My goto place for bargains on clothing and socks...

    My goto place for bargains on clothing and socks is Sierra Trading Post. I generally pay between 10 and 20% of the going rate for overstock and last years model. Here is a link for heavyweight...
  23. I appreciate posts with pics, but your are so...

    I appreciate posts with pics, but your are so small that I cannot see any detail....
  24. Nothing to be suspicious about. At this point,...

    Nothing to be suspicious about. At this point, just considering the possibilities for commercialization. If it does go forward, there will be complete specs, videos and early adopters to provide...
  25. Gcode software would be no problem. Fancy...

    Gcode software would be no problem. Fancy graphical software, tuned for specific controls or machine builders is a different matter. I will investigate the availability of Renishaw probe bodies at...
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4