Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Booze Daily

Page 1 of 57 1 2 3 4

Search: Search took 0.04 seconds.

  1. We should be friends.

    We should be friends.
  2. This is absolutely no help to the OP but reminded...

    This is absolutely no help to the OP but reminded me of a funny story.

    I had an operator work for me one summer. The lathe threw a low lube alarm. He thought that meant it needed coolant.
    So he...
  3. Replies
    24
    Views
    871

    Check #3020-#3025. System Variables | Customer...

    Check #3020-#3025.
    System Variables | Customer Resource Center
  4. Replies
    20
    Views
    701

    Sounds like more than $300 worth of figuring....

    Sounds like more than $300 worth of figuring.
    I'd buy the tool.
  5. Replies
    19
    Views
    580

    Why's that? I've changed mine several times, but...

    Why's that? I've changed mine several times, but I don't know if I touched the stylus or not.
  6. Replies
    19
    Views
    580

    Check the batteries.

    Check the batteries.
  7. I don’t mind. The owner and his employees are...

    I don’t mind. The owner and his employees are just trying to stay afloat.
    Just like me.
  8. Replies
    14
    Views
    896

    That’s really nice. You should see my machines....

    That’s really nice. You should see my machines. And I bought them brand new.
  9. Nope. We usually go to the little ma and pa...

    Nope. We usually go to the little ma and pa places in town.
    Burger, fries, couple beers for me and the wife.
    Used to be about $35 after tip. Now it's about $43 after tip.
  10. Replies
    17
    Views
    715

    The ones I have seen all have proprietary thread...

    The ones I have seen all have proprietary thread forms, I guess to differentiate themselves from the competition.
  11. Replies
    611
    Views
    39,892

    Like these? 302527

    Like these?

    302527
  12. Switch them to COD. Wait til the Chap 11...

    Switch them to COD. Wait til the Chap 11 finishes up, then decide if you want to go back to terms.
  13. Looks like something out of a 70's porn movie.

    Looks like something out of a 70's porn movie.
  14. Replies
    65
    Views
    3,071

    Apparently not

    Apparently not
  15. Replies
    65
    Views
    3,071

    JHC. Can’t one of you be the bigger person and...

    JHC. Can’t one of you be the bigger person and ignore the other instead of dragging this from topic to topic thru the whole forum?

    Go offline and get a room already.
  16. We’ve gone out to dinner every couple weeks. I’ve...

    We’ve gone out to dinner every couple weeks. I’ve noticed our typical bill has gone up about 20%.

    If they added a Covid surcharge instead of raising prices, would the surcharge go away eventually?
  17. That's illegal where I live.

    That's illegal where I live.
  18. Replies
    6
    Views
    304

    The tool probe is calibrated by a tool of known...

    The tool probe is calibrated by a tool of known length.(as measured from the face of the spindle to the tip of the tool)

    When you measure your tools, the lengths are recorded as length from the...
  19. That is the whole sub-program. The first half of...

    That is the whole sub-program. The first half of the program pushes the bar and checks for an end-of-bar signal.

    When it sees the end-of-bar it jumps to the second half of the program and pushes...
  20. Replies
    65
    Views
    3,071

    Written stuff is easy to misinterpret. Just look...

    Written stuff is easy to misinterpret. Just look at this forum.

    I tend to give the benefit of the doubt in most cases. Maybe he meant "this situation" is not good.
    Not necessarily "your...
  21. Grainger sucks

    Grainger sucks
  22. Replies
    11
    Views
    797

    Could you drill your 6mm hole small and stab it...

    Could you drill your 6mm hole small and stab it with an endmill?
    It will make your breakthrough cleaner.
  23. Maybe split the difference?

    Maybe split the difference?
  24. Replies
    42
    Views
    2,305

    You must have some really long cycle times.

    You must have some really long cycle times.
  25. Replies
    611
    Views
    39,892

    I'm still on my starter wife. My next wife is...

    I'm still on my starter wife.
    My next wife is going to be rich.
Results 1 to 25 of 1422
Page 1 of 57 1 2 3 4