Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Hodge

Page 1 of 26 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    37
    Views
    26,895

    Look, two spammers with one old thread, bonus...

    Look, two spammers with one old thread, bonus points for first post apiece
  2. Don't forget a valid driver's license.......

    Don't forget a valid driver's license.......
  3. Chin up now, you may find you are equal to a...

    Chin up now, you may find you are equal to a certain fellow by the name of Hugh Glass
  4. Replies
    318
    Views
    10,056

    Very carefully, you only get one try.....

    Very carefully, you only get one try.....
  5. Replies
    15
    Views
    1,015

    Agreed, though at this point it's advice falling...

    Agreed, though at this point it's advice falling on deaf ears so to speak.
  6. Replies
    67
    Views
    3,418

    Farmers. Com......

    Farmers. Com......
  7. Replies
    15
    Views
    1,015

    Based on what you've told it sounds more like a...

    Based on what you've told it sounds more like a parts machine/ basket case. Unless the majority of the parts are there(90% or more) you'll spend more time and money attempting to put it to rights...
  8. Replies
    67
    Views
    3,418

    All joking aside I have popped the seals off the...

    All joking aside I have popped the seals off the sealed bearing and regreased for longer life
  9. Replies
    67
    Views
    3,418

    And there you have it..... you've blown the...

    And there you have it..... you've blown the bearings....:D
  10. Replies
    30
    Views
    1,963

    Correct me if I'm mistaken, but wouldn't the...

    Correct me if I'm mistaken, but wouldn't the cutter bar interfere in getting a proper measurement?
  11. Replies
    11
    Views
    624

    pictures of course.....and welcome to the forum

    pictures of course.....and welcome to the forum
  12. Depends on who is in charge and their definition...

    Depends on who is in charge and their definition of "greater good". Think about that for a bit.
  13. Replies
    5
    Views
    616

    While I'm sure this thread will generate some...

    While I'm sure this thread will generate some interest, you might want to check out the selling and participation guidelines.
  14. Replies
    5
    Views
    976

    Get in some of the political discussions and...

    Get in some of the political discussions and agitate a bit......
  15. Replies
    50
    Views
    2,057

    Just an observation, not meant to be snarky, I...

    Just an observation, not meant to be snarky, I would think twice before removing/ replacing the existing drive system. It's real easy to lower the performance, much harder to improve on the factory...
  16. Replies
    86
    Views
    3,922

    If all else fails you could introduce a ravenous...

    If all else fails you could introduce a ravenous tribe of thermites to the pallet and they will quickly chew the wood from underneath.....
  17. Replies
    25
    Views
    1,437

    Admittedly I'm biased in favor of a rpc for its...

    Admittedly I'm biased in favor of a rpc for its simplicity and longevity. But $1500 for a 10hp rpc is overpriced quite a bit for someone capable of doing it themselves. I'm thinking $500 tops and...
  18. Replies
    86
    Views
    3,922

    Good call, not nearly as expensive as a damaged...

    Good call, not nearly as expensive as a damaged lathe. It's not a hard job if you have been exposed to this type of work but can be daunting if not.
  19. Replies
    19
    Views
    1,355

    I hesitate to put a value on something I'm not...

    I hesitate to put a value on something I'm not buying. However, provided it's in decent condition and location doesn't affect value excessively $1000 is not a bad starting point. Seems to have a...
  20. Replies
    10
    Views
    974

    That closer will be a big help for him. Your...

    That closer will be a big help for him. Your right the colletts themselves are easy enough to acquire. Is the handle for the turret leaned up on the backside of the pic?
  21. Replies
    10
    Views
    974

    Did you get a collett closer and colletts with it?

    Did you get a collett closer and colletts with it?
  22. Replies
    285
    Views
    69,920

    Or the humor....

    Or the humor....
  23. Replies
    17
    Views
    1,256

    Is that thickness dim. Correct or off by a...

    Is that thickness dim. Correct or off by a decimal point? If thin I would consider using a cutting disc or jigsaw against a guide then cleanup the edges.

    On edit: after further reading I see SAF...
  24. Replies
    16
    Views
    1,653

    My pardon, nicotine gum, of course

    My pardon, nicotine gum, of course
  25. Replies
    16
    Views
    1,653

    "Today, the inverter just started smoking." ...

    "Today, the inverter just started smoking."

    You realize gum and patches are available....
Results 1 to 25 of 635
Page 1 of 26 1 2 3 4