Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Elwood1968

Page 1 of 5 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    6
    Views
    457

    Four wires? The three three-phase leads and a...

    Four wires? The three three-phase leads and a ground? Interesting, because my Toolmaster 1B only has a three-wire circuit interrupter. Can you post a photo of the electrical panel on your...
  2. Replies
    6
    Views
    457

    Does your Toolmaster have a rotating handle on...

    Does your Toolmaster have a rotating handle on the door of the electrical cabinet? This handle mechanically connects to a disconnect switch (might be labelled as a "circuit interrupter" on the...
  3. Email sent. Thanks!

    Email sent. Thanks!
  4. Still looking for a taper attachment. ...

    Still looking for a taper attachment.

    262425262426
  5. Still looking for a steady rest and/or follower...

    Still looking for a steady rest and/or follower rest for a Cincinnati Hydrashift 12-1/2" or 13" swing.

    262423262424
  6. Replies
    2
    Views
    635

    Here's a screencap from a different Cintilathe...

    Here's a screencap from a different Cintilathe brochure, showing the speeds and feeds tables for English and metric QCGBs on the 10" and 12-1/2" machines. If this is too small to read, PM me your...
  7. Replies
    6
    Views
    980

    You've pulled the QCGB from the headstock, and...

    You've pulled the QCGB from the headstock, and can observe the gears from the back (open) side? Could you post some photos or even a short video as you move the levers to show what is (and is not)...
  8. PM sent re No. 44

    PM sent re No. 44
  9. Nice that you have that optional worklight reel. ...

    Nice that you have that optional worklight reel. They're hard to find. When you've got it wired up and working, please post some photos.

    Not sure what the hole looks like on the top of your...
  10. Looks to me like you have the remains of the...

    Looks to me like you have the remains of the factory optional worklight, which was wired into the 120v control circuit. The bowl thing appears to be the cord reel that automatically payed out and...
  11. Replies
    6
    Views
    980

    If your Cintilathe is like the one in the TrayTop...

    If your Cintilathe is like the one in the TrayTop manual from 1952, the C-D-E shifter is very similar to the one used in the later Hydrashift lathes like mine. A simple arrangement of a lever...
  12. Congrats on getting the old lathe running again....

    Congrats on getting the old lathe running again.

    Seven hundred PSI!!! I'm surprised the pump and fittings tolerated that pressure. That's a lot more than the rated maximum pressure according to...
  13. No one has posted a reply, but I purchased a...

    No one has posted a reply, but I purchased a range of the strainer sizes from General Filter to experiment with. I believe that the strainer element that was in my Hydrashift when I bought it was...
  14. I had the hydraulic block and forks completely...

    I had the hydraulic block and forks completely disassembled on my Hydrashift. When I put it back together, I spent some time measuring the throws of each gear set, and transferring those...
  15. When I first got my Hydashift, the little yellow...

    When I first got my Hydashift, the little yellow pointer at the two-o'clock position to the speed selection dial was missing, and the mounting hole in the headstock was partially filled with oil and...
  16. Glad you found it in time to prevent additional...

    Glad you found it in time to prevent additional damage.

    By "vertical shift fork" do you mean the fork that moves the Pullmore clutch hub (aka "slipper sleeve") left (to engage the clutch) or right...
  17. If you don't see oil flowing in the sight glass...

    If you don't see oil flowing in the sight glass when the spindle is (or should be) turning, then check that the oil line from the distribution block to the sight glass is routed correctly and not...
  18. FS: Cincinnati Superflex / Monoset / Toolmaster / 3CH Collet Package

    Selling the following Cincinnati "C" type collets as a package:

    35/64"

    19/32"

    5/8"

    3/4"
  19. Perhaps moving it (twice?) did something, from...

    Perhaps moving it (twice?) did something, from stirring up sludge in the headstock sump that ended up plugging the strainer, to knocking one or more of the shift forks out of adjustment. Pulling the...
  20. Replies
    8
    Views
    1,492

    I think that the OP is looking for a dividing...

    I think that the OP is looking for a dividing head tailstock (aka footstock). The one in that ebay listing appears to be for a very old Cincinnati (maybe) engine lathe.
  21. Replies
    8
    Views
    1,492

    Yep, that's the head. I remembered that thread,...

    Yep, that's the head. I remembered that thread, but couldn't find it to post the link. Thanks.


    Sorry, I don't have a Cincy horizontal mill tailstock or number plates to trade, but they're out...
  22. Replies
    8
    Views
    1,492

    That's a tailstock for a Toolmaster mill index...

    That's a tailstock for a Toolmaster mill index head. The "6JKA" indicates a Toolmaster, and the "5C" is a 1955 build year. The Toolmaster had a unique indexing head.

    255402

    If you ever want...
  23. Replies
    26
    Views
    3,877

    PM sent about the clutch. Thanks!

    PM sent about the clutch. Thanks!
  24. Replies
    8
    Views
    1,414

    F-M continued to build opposed piston diesel...

    F-M continued to build opposed piston diesel prime movers at Beloit both before and long after locomotive production ended (and still does today, I think), so maybe the planer was used for finishing...
  25. Replies
    8
    Views
    1,414

    Excellent. :drool5: Since F-M built their...

    Excellent. :drool5:

    Since F-M built their last new locomotive around 1963, I wonder what they used it for?
Results 1 to 25 of 113
Page 1 of 5 1 2 3 4