Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: 4GSR

Page 1 of 60 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    11
    Views
    725

    I've seen a lot of Micarta used in my earlier...

    I've seen a lot of Micarta used in my earlier years of life on machine members. Holds up reasonable good on unhardened ways. Also used Nylatron NSB use later on. It has moly added to give the...
  2. Replies
    10
    Views
    720

    John cornered the market with all of the steadies...

    John cornered the market with all of the steadies out there with his grinder.;)
  3. Replies
    11
    Views
    1,406

    You definitely not going to find anything used...

    You definitely not going to find anything used that would be ready to go here in TEXAS. UNLESS you buy new.

    As I said above, I have one here that needs a little cleaning and oiling and the...
  4. Replies
    24
    Views
    1,541

    We need pictures!!! Can't tell you anything...

    We need pictures!!! Can't tell you anything without pictures. Also the serial number, which is stamped between the Vee's at the tail stock end of the bed. BTW- South Bend Lathe did not build a 8"...
  5. Replies
    10
    Views
    720

    Must be having a wet dream asking that much for...

    Must be having a wet dream asking that much for it! Or thinks he's going to get that much for it.:o
  6. Replies
    18
    Views
    2,196

    Need to change the title to small antique lathe....

    Need to change the title to small antique lathe. And have the thread moved over to the Antique Forum.
  7. Ion Nitriding- There is a place in Conroe, TX...

    Ion Nitriding- There is a place in Conroe, TX that does Ion Nitriding. Used to go by the name Magnum Metal Treating or Magnum Heat treat. Been several years since I've used them. They may do ion...
  8. Tool-Flo in Houston will do it for you if the...

    Tool-Flo in Houston will do it for you if the quantity is high enough. If they won't do it for you direct, ask for a cutting tool distributor you can go thru to get it done. I've seen some gun...
  9. Replies
    15
    Views
    1,000

    I was expecting it to be a piece of junk like a...

    I was expecting it to be a piece of junk like a Indian made center I bought to put with a lathe I sold off a couple of years back. You could wiggle the center point on it. This one ran just as good...
  10. Replies
    6
    Views
    824

    But no postage stamp sheets were used? Or even...

    But no postage stamp sheets were used? Or even rejected ones.
  11. Replies
    15
    Views
    1,000

    Here's a live center I just bought and tried out...

    Here's a live center I just bought and tried out this morning. Was very shocked how well it performed. Your mileage may vary.

    MT2 Live Center Morse Taper Precision 0.000197'' Long...
  12. Replies
    6
    Views
    824

    What's the deal with the funny shaped hats? is...

    What's the deal with the funny shaped hats? is that to keep the little "dots" from getting in the hair?
  13. Replies
    6
    Views
    798

    For that No. 3 universal horizontal mill I had,...

    For that No. 3 universal horizontal mill I had, it must have been made after 1913. It was S/N 867, and according to the catalog, the attachments would only work on machines below S/N 650. All the...
  14. Replies
    11
    Views
    1,406

    Shawn, Where are you located here in Texas? ...

    Shawn,

    Where are you located here in Texas?

    If interested, I have a older BP clone here that has decent ways on it. Just needs a little TLC to get it back to running. It's noway of being a...
  15. Replies
    6
    Views
    798

    John, Do you by chance have a copy of that page...

    John, Do you by chance have a copy of that page out of the catalog you could send me? Ken
  16. Replies
    3
    Views
    544

    Very unusual to find a Model X without a chip...

    Very unusual to find a Model X without a chip pan. Almost like a woman without clothes.:o
  17. Replies
    16
    Views
    1,521

    In past lives, we had problems with investment...

    In past lives, we had problems with investment castings not responding to induction heat treating. The surface to about .010" deep would not get hard. Had to do with with the diffusion of carbon...
  18. I have a 6" 3-jaw and 6" 6-jaw chuck on my 9"...

    I have a 6" 3-jaw and 6" 6-jaw chuck on my 9" SBL. I found it to have much better capacity and a tad better holding power than that of a 5" 3-jaw chuck.
    It's funny, I just mounted a 5" 3-jaw chuck...
  19. Replies
    29
    Views
    2,480

    https://www.practicalmachinist.com/vb/images/metro...

    https://www.practicalmachinist.com/vb/images/metro/blue/misc/quote_icon.png Originally Posted by johnoder https://www.practicalmachinist.com/vb/images/metro/blue/buttons/viewpost-right.png
    when I...
  20. Replies
    14
    Views
    1,143

    Just installed three of them in my house...

    Just installed three of them in my house including a 24,000 BTU unit in my garage/shop. It's a two car garage, 20 x 20 roughly with 8 foot ceiling. No insulation in the walls or ceiling. First day...
  21. Replies
    21
    Views
    2,118

    Especially when it is Inconel 718 !!!:eek: Must...

    Especially when it is Inconel 718 !!!:eek: Must be for another part for the oilfield, spring energizer for a seal. Oh, could be for the petrochemical industry, too. Most made from X750.
  22. Replies
    21
    Views
    2,399

    That floor plate looks like one used with a...

    That floor plate looks like one used with a horizontal boring mill or RA drill press. Just saying.
  23. Replies
    29
    Views
    2,480

    I have some stray one's in my stash. I'll have...

    I have some stray one's in my stash. I'll have to look and see what I have. Don't hold your breath!

    Ken
  24. Replies
    7
    Views
    12,368

    I am retired and no longer have access to any of...

    I am retired and no longer have access to any of these threads. Please do not PM me for information on these threads.

    Sorry, Ken
  25. Replies
    43
    Views
    29,673

    Resurrecting an old thread. I heard recently...

    Resurrecting an old thread.

    I heard recently that Sulmberger (sp) is spinning off the old "Drilco" line and a couple of other product lines. They are also selling most off the property at the...
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4