Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Peter from Holland

Page 1 of 60 1 2 3 4

Search: Search took 0.05 seconds.

  1. Replies
    19
    Views
    956

    You could adapt the pressure angle of your...

    You could adapt the pressure angle of your gearset so the teeth roll as much as possible and rub as little as possible
    Also look into the oil you are using and its level
    I noticed a 3DB...
  2. Replies
    19
    Views
    956

    I have some mastergears for the rolltester for...

    I have some mastergears for the rolltester for sale if you want to go that route

    Peter
  3. Replies
    695
    Views
    47,572

    To adjust those bevel gears Klingelnberg has some...

    To adjust those bevel gears Klingelnberg has some documentation of how to do it Also a indication of play is given
    If you want it just give me a PM I do not want to post it here for copyright...
  4. Replies
    76
    Views
    6,290

    Are you planning on using it on 240Volts single...

    Are you planning on using it on 240Volts single phase
    How big is your fuse then
    Also wire your motor for 220 volts then

    In Amerika a 50Amps fuse in a domestic house is normal perhaps Not so...
  5. I have several manuals But all in German Peter

    I have several manuals But all in German

    Peter
  6. That small motor is indeed a DC motor 160 Volts...

    That small motor is indeed a DC motor 160 Volts I would not call it low voltage
    The speeds and voltage are on the name plate
    Peter
  7. To power up the feedmotor you have to press the...

    To power up the feedmotor you have to press the third and fourth button from the left simultaniously (bottem row) Thats what to do first
    The far right one is rapids You should hear the motor if...
  8. Replies
    14
    Views
    1,020

    I uploaded it to Wetransfer You should have a...

    I uploaded it to Wetransfer
    You should have a e-mail from Wetransfer with a link where you can download it

    Peter
  9. Replies
    14
    Views
    1,020

    160 yes ;) You should have asked for a parts...

    160 yes ;)
    You should have asked for a parts manual
    I have even one as a PDF file
    Still can send it over if you like

    Peter
  10. Replies
    32
    Views
    1,862

    Heidi is Swiss Proper German name would be...

    Heidi is Swiss
    Proper German name would be Gretha

    Nice machine

    Peter
  11. To me a scraped CI surfaceplate spots much better...

    To me a scraped CI surfaceplate spots much better as a granite one
    So for scraping I save the CI plates The granite plates I sell

    Peter
  12. Replies
    14
    Views
    1,020

    You bought that machine in 2005 wasn`t it? And...

    You bought that machine in 2005 wasn`t it? And just now you find out about the door:)
    How is the 150 doing BTW

    Peter
  13. Encoder would be it for me too And dont be...

    Encoder would be it for me too
    And dont be picky as on many DRO`s you can adjust the unit of measurement in anything you like
    I would get hold of a dro with 4 scales and the possibillity to...
  14. I can confirm this as I have a few But it was ...

    I can confirm this as I have a few
    But it was also because paint got eaten up by the oil contaminating it


    peter
  15. If it was metric A m6 dowel pin with a H7 reamer...

    If it was metric A m6 dowel pin with a H7 reamer wil give the proper fit

    Peter
  16. If you want to grind the shoulder too set the...

    If you want to grind the shoulder too set the wheel at a 45Dgr angle and dress a 90Dgr angle on it
    Keep in mind you do not get a sharp corner
    If you grind with the side of the wheel you...
  17. Replies
    24
    Views
    1,763

    That is a swing arm you can bolt the angle head...

    That is a swing arm you can bolt the angle head to and swing it out of the way for horizontal mode

    Here is a example
    ...
  18. Replies
    24
    Views
    1,763

    This is one of the rare events I understand and...

    This is one of the rare events I understand and totaly agree with you :D

    Peter
  19. Replies
    24
    Views
    1,763

    Ross Notice this You are familiar with your...

    Ross
    Notice this

    You are familiar with your machine But what if you have to start from scratch and then were on the machine just 1 hour a week ?
    Oke with newer machines and younger people...
  20. This one can do 10mm round For flat it needs...

    This one can do 10mm round
    For flat it needs some tweaking I guess
    https://www.youtube.com/watch?v=oVguMTNP98E

    Peter
  21. Its voor placing the lever operated draw bar ...

    Its voor placing the lever operated draw bar

    Peter
  22. Replies
    24
    Views
    1,763

    If I wanted to make money with a milling machine...

    If I wanted to make money with a milling machine I would go CNC No doubt
    But these machines I sell to R&D and maintenance departments who use them now and then No chance to learn CNC talk
    But...
  23. I have seen this with a odtimer also for T slots...

    I have seen this with a odtimer also for T slots IIRC
    I looked on the internet but could not find anything So I made up a quick and dirty drawing
    ...
  24. Replies
    24
    Views
    1,763

    Zephyrous I can help you out on that one I also...

    Zephyrous
    I can help you out on that one I also have its bigger brother Happy to sell it to you:D
    Also in pristine condition
    Travels 500x500x380
    ...
  25. Replies
    24
    Views
    1,763

    A link to the page where my machine is still...

    A link to the page where my machine is still offered
    I took of the sticker as I am going to fix that...
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4