Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: rons

Page 1 of 60 1 2 3 4

Search: Search took 0.07 seconds.

  1. Replies
    6
    Views
    519

    I remember them pretty good when parting 1"...

    I remember them pretty good when parting 1" diameter aluminium bar...

    289996
  2. Thread: Converter repair

    by rons
    Replies
    21
    Views
    1,067

    Not always except here... There are two run...

    Not always except here... There are two run capacitors and one pfc capacitor.
  3. Thread: Converter repair

    by rons
    Replies
    21
    Views
    1,067

    A RPC that is balanced will have two run...

    A RPC that is balanced will have two run capacitors. Each cap connected from one line to the generated leg.

    I suggest that you go seek some termite help. Gives him something to do.
  4. Thread: O.T.CBD oil

    by rons
    Replies
    44
    Views
    3,431

    If you go for the Indica variety then that is...

    If you go for the Indica variety then that is supposed to relax your body. There is no head high.
  5. Thread: Converter repair

    by rons
    Replies
    21
    Views
    1,067

    If the eight run caps had been all connected in...

    If the eight run caps had been all connected in parallel then that means one equivalent run cap equal to 480uf. So does that mean the balance was so great.
    I doubt it. You could do better.
  6. Replies
    2
    Views
    284

    The two slotted set screws that hold the upper...

    The two slotted set screws that hold the upper and lower part of the gauge to the front of the quill?

    I couldn't remove the top one. It is locked in place by a vertical hole with what I thought...
  7. Never liked the excessive slop in the Kurt vise...

    Never liked the excessive slop in the Kurt vise mount holes. So I made a couple of bushings that align the bolt to vertical. Tightening operations on the vise to
    get it lined up are reduced and at...
  8. 115V would mean 115vac. RMS value = .707 Peak...

    115V would mean 115vac. RMS value = .707 Peak value. Peak value = 1.414 * 115 = 162.
  9. That is where I would start. That is the voltage...

    That is where I would start. That is the voltage for all your push button controls.
    Disconnect all control transformer loads and then take a reading to see if it's 115v. Maybe add one load at a time...
  10. Replies
    45
    Views
    2,169

    Post 38 #4. If we have to tap something in place...

    Post 38 #4. If we have to tap something in place or in a vise we try to figure out the best way to guide the tap straight and we use spiral point taps.

    If you are tapping by hand with a free-hand...
  11. Replies
    45
    Views
    2,169

    I call them high performance taps at the counter....

    I call them high performance taps at the counter. That's all they need to know. Never got junk yet. Nothing made in China as well.
  12. Replies
    45
    Views
    2,169

    My 1/4-20 taps have a class of fit equal to GH3....

    My 1/4-20 taps have a class of fit equal to GH3. It is stamped as GH3. It is .0015 above normal diameter.
    Bought the taps when the class of fit over the counter buy usually gets you a GH3 if you...
  13. Measure the capacitors individually.

    Measure the capacitors individually.
  14. Replies
    55
    Views
    2,200

    Get a True RMS Fluke meter.

    Get a True RMS Fluke meter.
  15. I bought a J.S.T. Corporation (Taiwan) crimper...

    I bought a J.S.T. Corporation (Taiwan) crimper tool 10015-JST for $20 in a surplus store. The same tool from a reputable USA company was $350.

    This one is like the one I bought. Replaceable jaws...
  16. Replies
    36
    Views
    2,407

    I do those once in a while. Not in big batches. ...

    I do those once in a while. Not in big batches.

    Make a thick coin with a threaded hole in the center.
    Insert your screw with the end sticking out the other side.
    Add a back-stop to a coin sized...
  17. Replies
    6
    Views
    999

    Those wafers can be used to make chemical...

    Those wafers can be used to make chemical resistant washers/bushings.
  18. They have been using putty to balance rotors for...

    They have been using putty to balance rotors for something like 20+ years. Sloppy.

    Instead, I run either a 12-24 or 1-4-20 not on those aluminium studs. Then screw on different thickness nuts....
  19. If your capacitors are connected as 'run'...

    If your capacitors are connected as 'run' capacitors then there is no need for a current bleed resistor(s).
    The capacitor will discharge through your motor copper windings.
  20. Page gone - means censorship.

    Page gone - means censorship.
  21. I would have never guessed...

    I would have never guessed...
  22. Open it and identify what capacitors are...

    Open it and identify what capacitors are connected.
  23. My first and last pre-built RPC was the one you...

    My first and last pre-built RPC was the one you have. I returned it and have no regrets. It does have a Baldor motor but it is not comparable to a
    5Hp motor. The rotor is lightened and there is one...
  24. Replies
    36
    Views
    1,576

    The Starret parts 1-800 order line was nice to...

    The Starret parts 1-800 order line was nice to have available when I wanted to restore a damaged caliper.

    I don't own any of the new (import) copies. Copies in that they are trying to make the...
  25. Replies
    9
    Views
    763

    Like this? See how they do it for threading. ...

    Like this? See how they do it for threading.

    288370
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4