Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: D.D.Machine

Page 1 of 40 1 2 3 4

Search: Search took 0.03 seconds.

  1. looks like 2 opps ,,, 3/8" by 3/4" stock layed ...

    looks like 2 opps ,,, 3/8" by 3/4" stock layed flat on a 4th … mitee bite clamps between two strips and do a row of tapers ,, turn 90* and do the side holes and cut down in thickness ,, turn 90...
  2. Replies
    19
    Views
    1,353

    Read post #3 Its super simple to get around...

    Read post #3

    Its super simple to get around there door switches...
  3. I have a feeling your pump is cavitating do to...

    I have a feeling your pump is cavitating do to the little amount of flow its seeing ,,, you might try a dump valve so you can increase the flow going throe the pump ,,, I have had lathe pumps do that...
  4. Replies
    2
    Views
    219

    someone must know ?

    someone must know ?
  5. Replies
    18
    Views
    1,021

    I would contact Doosan and check on a new spindle...

    I would contact Doosan and check on a new spindle ,, its my understanding that Daewoo machinery went under and Doosan got the rights to Daewoo right before Doosan started to fold and they got bought...
  6. Replies
    27
    Views
    1,793

    You well need a second fan to clean all the chips...

    You well need a second fan to clean all the chips out of the umbrella tool changer …
  7. Replies
    27
    Views
    1,793

    Redline fan only uses one pocket on my 24 and 30...

    Redline fan only uses one pocket on my 24 and 30 pocket haas mills,,, I think I payed right about $169 for them but it might have been a end of the year sale ,, I make up a wish list and buy a lot...
  8. Replies
    9
    Views
    543

    sounds normal to me ,, run it for a few hours and...

    sounds normal to me ,, run it for a few hours and pop the tool and stuff a finger in the hole ,,, it should feel warm but not hot …
  9. it looks like it done in the has control and just...

    it looks like it done in the has control and just a little of it in the program ,, its just been kinda tricky to get a grip on it do to the info being spread between years and controls.
  10. I put ball screws on a bridgeport years and soon...

    I put ball screws on a bridgeport years and soon sold the mill do to them ,,, when ever you lock a table the table moves ,,, with the acme screws I can just put the lock on so it starts to drag some...
  11. Advanced Tool Manahement for DUMMIES ?

    I am trying to wrap my brain around the Advanced tool management on both original control and the NGC control and well I am finding a lot of info about it non of it I have found really does a good...
  12. Replies
    27
    Views
    1,793

    even at just 6K they blow the coolant EVERY WEAR...

    even at just 6K they blow the coolant EVERY WEAR ,, but as long as you program it not to go close to the limits in Y axis it does not seem to blast chips and crap up under the table ,,, The redline...
  13. Replies
    2
    Views
    219

    when you find out how to Zero it please post it...

    when you find out how to Zero it please post it up ,,
  14. Replies
    28
    Views
    2,082

    Boeing pays there workers a vary well and they...

    Boeing pays there workers a vary well and they have always been a company that bounces up and down, I have been in the machinist trade for 37 years just outside of seattle and anyone that goes to...
  15. Replies
    27
    Views
    1,793

    I use a redline one every day and like it ,,, I...

    I use a redline one every day and like it ,,, I run it at 6k and stay about 6" over the fixtures ,,, it does not a great job of blocking of the parts and the work area ,, but does not get the coolant...
  16. Replies
    30
    Views
    2,292

    looks like a mill part to me ,,, make them two at...

    looks like a mill part to me ,,, make them two at a time and do the bottom of the knob first opp then flip them over and hold the two stems and cut the finger groves ,,, two ops and there done ,,, a...
  17. first pull the cover and see if the cap is a 110V...

    first pull the cover and see if the cap is a 110V or a 220V … I think they use defend caps all depending on what voltage your wiring it up for … I well say that that type of pump works great but they...
  18. Not to take away from the OP but this thread...

    Not to take away from the OP but this thread reminded me of a Bridgeport copy I got at Boeing surplus back in the early 90`s ,,, Craig the guy that ran the used equipment had walked me into the back...
  19. Its my understanding that it is up to the HFO on...

    Its my understanding that it is up to the HFO on what they carry on there trucks … the HFO up here in Washington state is Selway ,,,, The local Ellison dealer up here is a Doosan seller and they are...
  20. I still have a 1943 B&S 2G that I use for just...

    I still have a 1943 B&S 2G that I use for just part off jobs and have never seen a new cnc that can even spit out half as many parts per day as they can. I run a lot of parts on a 6 second per part...
  21. Replies
    16
    Views
    964

    I thinking its something with the machine more...

    I thinking its something with the machine more than the pump? I run 4 Haas mills every day all 2015 and newer and have had no problem's with the pumps at all,, I had two mills show up with there...
  22. I had single phase pumps on my fadals and they...

    I had single phase pumps on my fadals and they burned out a LOT ,, I wired in a pull in contactor and changed to 3 phase pumps and got away from all of the starter BS that the single phase pumps had...
  23. there is some new ones on ebay for like $600 , I...

    there is some new ones on ebay for like $600 , I was looking at getting one for a washdown pump and then I would have a spare if I needed a coolant pump in a hurry

    I think selway in Washington...
  24. Replies
    16
    Views
    964

    I would check your program? T1 m06 (tool...

    I would check your program?

    T1 m06 (tool call)
    M08 (Coolant on)
    T2 ( next tool pre stage )
    M03 S12000 ( spindle on )
    G54 (fixture offset)
    G00 G43 Z.1 H01 D01 ( move...
  25. Replies
    16
    Views
    972

    I have moved a LOT of machines over the years and...

    I have moved a LOT of machines over the years and just go slow and think before EVERY move I make ,,, The only time I have ever really puckered up was getting the DNM7500 down off the truck ,, I had...
Results 1 to 25 of 978
Page 1 of 40 1 2 3 4