Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: propman

Page 1 of 8 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    0
    Views
    357

    Swivel angle plate

    Phase II 12 X 15 swivel angle plate little use in very good condition just surface dirt. $300.00 or best offer, contact [email protected] located in Delaware 19975
  2. Replies
    0
    Views
    311

    Phase II rotary table

    10" phase II vertical/horizontal rotary table very little use just sitting on the shelf $300.00 or best offer contact [email protected] located in 19975 Delaware
  3. Thread: radiial drill

    by propman
    Replies
    0
    Views
    469

    radiial drill

    no name on it but it does have a nice variable speed motor probably worth more than the drill. Take it away for $500.00 contact [email protected]
  4. Replies
    9
    Views
    1,166

    unknown radial drill

    had to reply to this post as I have an old beast with no name, it does have a variable speed motor and can be had for cheap.
  5. Thread: Acu-rite DRO

    by propman
    Replies
    4
    Views
    642

    the item has sold, thanks!

    the item has sold, thanks!
  6. Thread: Acu-rite DRO

    by propman
    Replies
    4
    Views
    642

    Acu-rite DRO

    2 Axis Acu-rite DRO from a lathe, scales are 48" & 12" Reader works fine but the cables were pulled out of the scales, unit was working fine until then. $200.00 Contact [email protected]
  7. Replies
    4
    Views
    1,453

    price reduced to $5000.00 send email to...

    price reduced to $5000.00 send email to [email protected]
  8. Replies
    8
    Views
    1,170

    I still have the VTL but we had to put the white...

    I still have the VTL but we had to put the white ghost to sleep
  9. Replies
    8
    Views
    1,170

    Bullard 42" VTL

    I have a 42" spiral drive Bullard for sale. Very little use 440 3 phase runs fine. $1000.00 and you have to move it. Machine weighs 25,000 lbs. Has a centrally located lifting eye, located in...
  10. Thread: center rest

    by propman
    Replies
    5
    Views
    820

    I sent you a PM but if you would please email me...

    I sent you a PM but if you would please email me it will make things much faster [email protected]
    Thanks
  11. Thread: center rest

    by propman
    Replies
    5
    Views
    820

    sorry but I don't know how to edit this but...

    sorry but I don't know how to edit this but reducing price: the roller steady rest is $100.00 and the 3 others are $150.00 for all. Email [email protected]
  12. Replies
    4
    Views
    1,453

    Price reduction to $6000.00

    Price reduction to $6000.00
  13. Replies
    4
    Views
    1,453

    lowering price to $8000.00 contact...

    lowering price to $8000.00
    contact [email protected]
  14. Replies
    4
    Views
    1,453

    tooling

    I forgot to post the tooling plus there are tools in the carousel and I'm up for offers
  15. Thread: center rest

    by propman
    Replies
    5
    Views
    820

    center rest

    I have 4 center rests, one is a roller type $250.00 and the others are $150.00 each or $400.00 for all three. I don't know what type of lathe they came off of. contact [email protected] or...
  16. Replies
    0
    Views
    370

    Everett abrasive saw

    I have a 7.5 HP Everett abrasive cut off saw, works fine 3 phase don't use it.
    $300.00 located in southern Delaware contact [email protected] or 302.436.5442
  17. Replies
    4
    Views
    1,453

    1995 Cincinatti Arrow 500

    I have a 95 Arrow with 2100 control. used very little and cut plastics run about 40 hours/year. in the past year had pendant replaced and most of the drives have been sent in for battery replacement...
  18. Replies
    7
    Views
    976

    Thanks tom but there are no dovetails except for...

    Thanks tom but there are no dovetails except for where the base unit slides into the bracket that holds the hole attachment to the lathe and that doesn't really matter as far as I see and once it is...
  19. Replies
    7
    Views
    976

    OK,I've taken the attachment apart and cleaned at...

    OK,I've taken the attachment apart and cleaned at least 20 years of smeg off and I find the (according to the manual) swivel bar key to be about .004 worn in the center part of the slide and of...
  20. Replies
    7
    Views
    976

    Well yes it happens closer to the chuck and I am...

    Well yes it happens closer to the chuck and I am going to take the attachment apart today and check for wear thanks to both of you for input. I have bought parts from latheman on this forum before is...
  21. Replies
    7
    Views
    976

    taper attachment

    I have a turn-nado 17" lathe that for years I've been machining tapers and all of a sudden on smaller shafts I started to get a spiral cut at the end of the taper. It did not seem like chatter and I...
  22. Replies
    6
    Views
    1,937

    My machine serial # is 54-72010 and I'm trying to...

    My machine serial # is 54-72010 and I'm trying to figure out how much oil should be pumping into the verticle head, I noticed today that thru the sight glass on initial start up I get a little flow...
  23. Replies
    6
    Views
    1,937

    Ok key issue solved now to the manual feed on the...

    Ok key issue solved now to the manual feed on the table. When I got the machine (military surplus) the electrical box was knocked off the machine and most of the wires were broken and of course all...
  24. Replies
    6
    Views
    1,937

    Yes, I tried with the holder with the dimple on...

    Yes, I tried with the holder with the dimple on both sides and it will not fit with the dimple facing either direction. I guess it will not hurt anything if the key stops are shortened?
  25. Replies
    6
    Views
    1,937

    OK, got the DRO installed and the coolant all...

    OK, got the DRO installed and the coolant all together and now I'm having an issue with a tool holder. I have a new cat 50 tool holder but I can't get it all the way in the spindle bore with both...
Results 1 to 25 of 185
Page 1 of 8 1 2 3 4