Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Brandenberger

Page 1 of 6 1 2 3 4

Search: Search took 0.00 seconds.

  1. There are shims for the cast iron bearings for...

    There are shims for the cast iron bearings for sale on eBay,
    If you are unsure of the right shim thickness (peel to the
    right thickness).

    I have an extra set, PM if you want them.
  2. Definitely an option of last resort, certainly. ...

    Definitely an option of last resort, certainly. And as a bonus, saves 50% on inserts! :)
  3. Replies
    14
    Views
    568

    Not really a question of "trying it" so much as...

    Not really a question of "trying it" so much as you would need to rate the VFD for the Locked Rotor Amps of the motor. Which would be rather massive for that motor.

    Why not wire the low voltage...
  4. pm incoming for arbor and tapmatic.

    pm incoming for arbor and tapmatic.
  5. Not sure what diameter and material you need but...

    Not sure what diameter and material you need but I've gotten copper and plastic tubing from fluidline systems in several diameters for bijur setups.
  6. Replies
    3
    Views
    245

    Hi, I just went and looked at the table screw...

    Hi,

    I just went and looked at the table screw assembly since it off my machine
    in the basement right now. Here is a picture of the casting on the left side
    of the table.

    271373

    Two...
  7. Replies
    3
    Views
    245

    I have a VN22LU which looks fairly similar to the...

    I have a VN22LU which looks fairly similar to the VN26, and I took the table off recently.

    First step was removing the screw assembly. I removed the right side screw assembly but leaving the...
  8. Wanted: wedge & screw for SPG face mill

    Hi,

    I got a massive ~10" facemill cutter with 12 SPG532 inserts. It's an old
    SECO (marked Fagersta Sweden 257.1). Was on a NMTB50 with a VN22L.

    Unfortunately it is missing one wedge and...
  9. Brown and Sharpe Horizontal mill heads at HGR

    Just saw these (two are listed), the price is right at $129.
    Not sure which machine they fit...

    Used Brown & Sharpe Machine Tool/part | HGR Industrial Surplus
  10. PM sent in case first sale doesn't happen......

    PM sent in case first sale doesn't happen...
    -Phil
  11. Mine is a 22L not a 26, so yours may differ. I...

    Mine is a 22L not a 26, so yours may differ. I found the same sludge in the cutterhead. I pulled it, cleaned it out, and soaked for a week in a bucket of diesel, spinning the spindle periodically,...
  12. No big problems doing this. Remove the screw and...

    No big problems doing this. Remove the screw and gib and ends, slide the table far enough out one side, put a table or rolling cart under it and lower the knee so the table is supported, then slide...
  13. Replies
    5
    Views
    604

    Hi, Yes, in the old thread you posted ...

    Hi,

    Yes, in the old thread you posted
    ...
  14. Replies
    5
    Views
    604

    Well... I removed a stop screw from the front but...

    Well... I removed a stop screw from the front but nothing else!
    Thanks, let me consult the diagram.

    Phil
  15. Replies
    5
    Views
    604

    Removing ram from VN22L

    Hi,

    I need to remove the ram from my machine,
    To clean and assess wear. Another forum
    Member had done this the smart way, using the table
    But I’ve already removed the table and saddle.

    If...
  16. Replies
    45
    Views
    6,539

    One other slight correction: There are...

    One other slight correction:

    There are actually two part numbers for the clutch driving plates. The rep at Palmer
    was helpful enough to determine that the picture I showed him was part number...
  17. Replies
    12
    Views
    1,387

    It seems like the ram (when locked in position)...

    It seems like the ram (when locked in position) needs to be parallel
    to the knee... if not then by extension the spindle axis is thrown off.

    My ram was similarly packed with chips, I haven’t...
  18. Replies
    12
    Views
    1,387

    Datum Surface for VN22L?

    Hi,

    I'm trying to determine what the best datum surface is for this VN22LU.

    The column surface has some fairly deep scoring, but also shows
    what I assume is original scraping from about 12"...
  19. Replies
    45
    Views
    6,539

    One other note: Twin Disc and Palmer Johnson...

    One other note: Twin Disc and Palmer Johnson still have the drawings of the clutch assembly pieces and parts lists for them. I'm not posting them here because they're noted as confidential on the...
  20. Replies
    45
    Views
    6,539

    Hi, This is an old thread, however I've just...

    Hi,

    This is an old thread, however I've just worked through the clutch removal
    for a VN22LU and wanted to add some details that might help others in the future.
    Daryl (from this thread) has been...
  21. Replies
    12
    Views
    1,387

    I ended up getting the saddle off (details in...

    I ended up getting the saddle off (details in another thread on the Van Norman forum (VN 22LU lower saddle removal).

    The condition of the underside of the lower saddle and
    top of the knee (with...
  22. Replies
    2
    Views
    563

    Removed the lower saddle finally after removing...

    Removed the lower saddle finally after removing gib.

    Underside of saddle has some fairly deep (probably .010"?) scoring.

    267165

    The dovetail top surface had been badly scored, and some...
  23. Replies
    2
    Views
    563

    I determined the front and sub-plate probably...

    I determined the front and sub-plate probably come out together, so I
    re-affixed the two with the 3 central hex bolts, and put threaded rod
    into the bolt holes that would affix the outer plate to...
  24. Replies
    2
    Views
    563

    VN 22LU lower saddle removal

    Hi,

    I'm working on my VN22LU, attempting to remove the lower saddle. As the nut and power feed spline shaft housing is screwed into the lower saddle with unreachable screws, I assume the only way...
  25. Replies
    2
    Views
    686

    As per the manual I have (VN 22L), "To obtain the...

    As per the manual I have (VN 22L), "To obtain the fee desired: First, lever "X-3" MUST be set in neutral position; next, the rotary feed seelctor knobs "X-1" and "X-2" are pulled out simultaneously...
Results 1 to 25 of 143
Page 1 of 6 1 2 3 4