Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: dalmatiangirl61

Page 1 of 46 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    13
    Views
    639

    I was skeptical first time I saw it, but it...

    I was skeptical first time I saw it, but it works! Wrap bearing in damp washcloth, place in micro, use 15 second bursts till you figure out correct time. It turns the water to steam to heat the...
  2. Replies
    13
    Views
    639

    I find using heat/cold makes bearing removal much...

    I find using heat/cold makes bearing removal much easier, its nice to be able to just pull a bearing off a shaft, or slide one on to a shaft, by hand, versus pullers and pressing or hammering them...
  3. Replies
    6
    Views
    391

    Lol, you beat me to it, I just watched that vid...

    Lol, you beat me to it, I just watched that vid and came over to post it. A tool we use every day, and I admit had never looked into the story behind it. The funny part to me was that I've had this...
  4. Replies
    13
    Views
    639

    I don't think a paint ball gun would do you any...

    I don't think a paint ball gun would do you any good, unless all you need is small short bursts. If you need to freeze something, get a CO2 fire extinguisher, or bottle, put part in shop rag, place...
  5. Replies
    3
    Views
    400

    USPS MO went in mail today, missed the cut0ff...

    USPS MO went in mail today, missed the cut0ff time for outgoing mail today, it will be in transit tomorrow, should arrive in Napa on thursday. Thank you.
  6. Replies
    3
    Views
    400

    I'll take it, PM incoming

    I'll take it, PM incoming
  7. Replies
    45
    Views
    2,651

    I ship every day, I can pack to survive a 20'...

    I ship every day, I can pack to survive a 20' fall, but cardboard, foam, and tape does not stand a chance being driven over by a truck. I've been purchasing quite a bit of tooling past few months,...
  8. Replies
    45
    Views
    2,651

    UPS offers overnight shipping from BFE, the catch...

    UPS offers overnight shipping from BFE, the catch is you have to meet the plane at the airport, at 7am:toetap:. Heck, we even have a UPS Customer Center, problem is its not staffed, ever. Usps and...
  9. You would be better off shopping the local...

    You would be better off shopping the local auctions and craigslist, that is where the scrappers find them. As mentioned above, the scrappers could care less about beating up a machine getting it...
  10. Replies
    45
    Views
    2,651

    Have they updated their gps system so they can...

    Have they updated their gps system so they can actually find an address? I've been accepting packages at Nv address for 18 years from USPS and Fedex, the UPS dolts still cannot f'ing find me....
  11. You want all original controls, and the use of...

    You want all original controls, and the use of the 2 speed motor, stick to an rpc. Do you see now why an rpc is easier:)
  12. I'm wondering if the Fogbuster can pass magots?

    I'm wondering if the Fogbuster can pass magots?
  13. Certainly looks like a well cared for machine,...

    Certainly looks like a well cared for machine, doubt its what most of us were envisioning, hope someone steps up to save it.
  14. Replies
    46
    Views
    2,927

    Hard to judge from a pic, but that looks like a...

    Hard to judge from a pic, but that looks like a crinkle surface. The old skillets are very smooth, I have a couple of Griswold, but most of my collection is no name stuff, most likely Wagner and BSR,...
  15. Replies
    40
    Views
    50,401

    I've got a selection of angle grinders, Makita,...

    I've got a selection of angle grinders, Makita, Bosch, and HF. I've been an advocate of the HF units for a while as they were cheap enough to buy several so you were not always swapping wheels, and...
  16. Replies
    30
    Views
    1,920

    That actually makes the concrete option easier:D....

    That actually makes the concrete option easier:D. Friends shop is a portable building, as he added machines he would cut floor open, frame a pad for machine, then pour full of concrete till level...
  17. Replies
    5
    Views
    488

    X2 on cool, I'm still waiting on something a bit...

    X2 on cool, I'm still waiting on something a bit smaller that will burn a hole thru a broken bolt that you can't reach.
  18. Replies
    46
    Views
    2,927

    The impetus for me to change to CI was looking at...

    The impetus for me to change to CI was looking at an unappealing grey steak grilled in a SS pan, it had every appearance of being boiled, yes I prefer grilling over an open flame, but at neg F temps...
  19. I looked at PODS website a few nights ago, no...

    I looked at PODS website a few nights ago, no info given on load capacity, just estimate of how many rooms of household goods they will hold. Before loading one full of even small machines, I would...
  20. The 2 speed aspect would be achieved by using a 2...

    The 2 speed aspect would be achieved by using a 2 speed motor like maynah shows, but that is a 3ph motor. Not sure if you can get a 2 speed motor in single phase, if you can I suspect it won't be...
  21. I've never heard anything like that. If you go...

    I've never heard anything like that. If you go single phase, for 3 to 5hp you will be needing 240V single phase, you can get 3 to 5hp motors with 1750 rpm, they cost more than 3450 rpm motors. You...
  22. Replies
    30
    Views
    1,920

    Friend with wood floor shop had same problem, he...

    Friend with wood floor shop had same problem, he solved it by cutting hole in floor, framing it in, then pouring full of concrete. Might not be an option for you:D

    Last time I saw his shop we had...
  23. Replies
    28
    Views
    1,811

    One of my cats, found as a stray kitten surviving...

    One of my cats, found as a stray kitten surviving on bugs, kills and eats just about everything she can, and still wants food at night. Her retarded child spends the day in the park staring at gopher...
  24. Replies
    10
    Views
    661

    I was digging around an old theater yesterday,...

    I was digging around an old theater yesterday, was quite surprised when I opened the circuit box and found the name Starrett. Really cool old box, full of copper and bakelite knife switches. Found...
  25. Replies
    28
    Views
    1,811

    Rented warehouse at first shop had an old 4'...

    Rented warehouse at first shop had an old 4' diameter hand dug well with a sheet of steel for a cover, someone removed the cover, I found 3 dead possums in the well, it was disgusting! We never drank...
Results 1 to 25 of 1126
Page 1 of 46 1 2 3 4