Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Phil in Montana

Page 1 of 18 1 2 3 4

Search: Search took 0.01 seconds.

  1. I put centers in a t%g shaft,put between centers,...

    I put centers in a t%g shaft,put between centers, dialed in and put 2 indicator , one at 12 and one at 9 o clock and run the full length of the bed....Adjust for tell stock error....Phil
  2. Replies
    26
    Views
    1,175

    Works just fine.If you preheat and post heat you...

    Works just fine.If you preheat and post heat you will not have hard spots and less warp...Phil
  3. Cleaning ugly oily floor hack saw mess 30 years worth...

    What is the easy/ best way to clean up the mess from a old hacksaw area? Hydrolic saw with a leak,cutting oil, rusty chips ect 30 years worth about, shop boy didnt do job, hi hi 20x20ft...cement...
  4. Replies
    28
    Views
    878

    Poll: If the studs fail, 1 do you get sued? 2 will...

    If the studs fail,
    1 do you get sued?
    2 will anyone get killed?
    3 will you have any liability of any kind?
    4 is it your truck?
    If No use anything you like...Phil
  5. I dont have what you want but something bigger,...

    I dont have what you want but something bigger, 36x72 pink starret from usaf, never used $500.00 plus boxing and shipping...Phil
  6. As my dad used to say " Heell you don't need a...

    As my dad used to say " Heell you don't need a machinist you need a priest" all kidding aside you will probably not get the tap out, buy a new casting and single point the threads, if you had a tap,...
  7. Thanks going to move it sat...Phil

    Thanks going to move it sat...Phil
  8. Replies
    13
    Views
    545

    DO NOT Breathe the dust, it can kill you in 20...

    DO NOT Breathe the dust, it can kill you in 20 years...Phil
  9. Replies
    24
    Views
    1,516

    No other models were the same... I have spare a...

    No other models were the same... I have spare a type 61, totally different, the 1610 or type 62 is a one of a kind...Phil
  10. Replies
    24
    Views
    1,516

    To retofit a taper attachment is a very big...

    To retofit a taper attachment is a very big deal... It is possible but you need to find a donor lathe to steel the parts from, no one is going to cut one up just to sell the ta...always buy a lathe...
  11. Still for sale 20k you load, I help...Phil

    Still for sale 20k you load, I help...Phil
  12. Replies
    14
    Views
    8,469

    Keep in mind on ng the kw will only be 60% of...

    Keep in mind on ng the kw will only be 60% of gasoline, and a lot harder to start cold...Phil
  13. I have 3 in Montana all gov surplus, like...

    I have 3 in Montana all gov surplus, like new...Phil
  14. Only 60 lbs?? 75 hp motor plus motor leads 1 lbs...

    Only 60 lbs?? 75 hp motor plus motor leads 1 lbs / hp= 75 lbs probly light but ok, dc field poles, inter poles, sires fieds maybe 70/80 lbs, comm and arm windinds 60/80 lbs, brass brush holder 10/15...
  15. A little pile of copper it is not, and for 2 hrs...

    A little pile of copper it is not, and for 2 hrs work at would come in at 125.00/hr at crap prices, hold on to it and you might get 500-750 for the copper and then there is the steel . You would not...
  16. Strip out the copper and forget it, the cost of...

    Strip out the copper and forget it, the cost of electricity to run it with demand would make the nat. dept look good,and the noise, ugly.There 250.00 in copper hiding in there...Phil
  17. Replies
    37
    Views
    2,154

    For a local saw mill I use to drill a 7/16 hole...

    For a local saw mill I use to drill a 7/16 hole in 5 ft in a 1 1/2 ram for a tempersonic encoder. A real pia. I would drill/ bore the first 6 inchs to get the hole going stright, then drill in stages...
  18. Replies
    181
    Views
    5,695

    Here in Montana some rejoice when the bear...

    Here in Montana some rejoice when the bear exports get et....Phil
  19. Replies
    7
    Views
    548

    If anyone wants, it will over the top in machine...

    If anyone wants, it will over the top in machine work, from hooking the lister diesel to 2, 5 speeds and the cut down of a dana 60 and 70, and speed increasing transfer case for 16 and 22 inch tires,...
  20. Use a B loc, use a very heavy wall in your...

    Use a B loc, use a very heavy wall in your hub...Phil
  21. Replies
    7
    Views
    548

    I like the shrink fit, and I can make a wide...

    I like the shrink fit, and I can make a wide piston for more grip, Just had two of my friends lay out 40k for a little compact tractor, In the planning stages of building my own...( I know, but 40k...
  22. Pam, or any spray on oil for cooking,...Phil

    Pam, or any spray on oil for cooking,...Phil
  23. Replies
    181
    Views
    5,695

    I think you have a very wrong idea, you DONT...

    I think you have a very wrong idea, you DONT scare off grizzleys, anything you do will attract them, then you will need a gun to stop them, they had a very bad temper, I know my silver mine was many,...
  24. Replies
    9
    Views
    733

    Not to rare, I have just like it...Phil

    Not to rare, I have just like it...Phil
  25. Replies
    7
    Views
    548

    A .020 shrink fit might be a little hard to do on...

    A .020 shrink fit might be a little hard to do on a 1 1/4 rod,I will do a test part, thanks Phil
Results 1 to 25 of 427
Page 1 of 18 1 2 3 4