Search:

Upside down air duster on the cutter can freeze it down enough to pop it
Mark

I was power work head inclined also
Mark

Most people I speak to think DT was not a bad deal as boss man, economy good, no wars, unemployment reducing, at the end of the day you can only judge by results, and they were ok, however I’m not...

Cev comes to mind, a good grade for forging does not automatically mean good for welding, I’d guess ( don’t have the equipment to verify since retiring)med carbon mid manganese so I guess they are...

What I was thinking , would it be possible to use audio to actually find out what frequency to avoid, like ringing a grinding wheel, bash it record the audio to give you a predictable chatter zone?,...

From my limited knowledge would it be fair to say chatter is in fact resonance?
You hit the natural resonant frequency of the system, to overcome somthing needs to change, speed feed clamping etc?,...

Probability theory, quantum golf, who knows but it’s interesting to think about
Mark

I see what you mean about sheathing a house, very pricey, however most houses are brick or block outside skin cavity with insulation and inside skin of 4” concrete or thermal blocks over here, I use...

Personally I hate osb, avoid it like the plague, however most of the sheet I use is birch ply, invariably Russian, quality is exceptional to be honest, some of the crap about is full of voids, we get...

Not entirely sure the stock market is machineing myself OT perhaps or confusion?,
Mark

Your gonna need a bigger lathe!
I’d be trying to design around that one myself, even if it’s an existing part, go up or down in size, way cheaper
Mark

It’s 3 phase yes, the only struggle will be rotational direction, if wrong switch any 2 lives, you may need to get an electrician to sort it if your stuck, no shame in that I have, no one knows...

We had one in work, and I’m sure I’ve told but I actually sliced meteor on it
(Ite, oil, hammerite,) cut quite easily,
I like do all, I have a start rite that’s quite good, but I’d prefer a do it...

Emuge DF NI taps are specifically ground cobalt plus tramps for the dreaded inco nightmare, plus if enough room a jet of coolant down the hole if blind or back coolant up the hole if through, sticky...

Lathes.co.U.K.,tony may have one, I think it’s a standard spline so theoretically you could do it on the lathe with a bit of direct indexing,
I have a Harrison 12” swing (L6?) wish the thing had a...

I had a set of whia stainless off my mate, they get supplied to the hospital, they don’t want carbon steel getting on their surgical stuff apparently, they were really nice, since I’ve tried the...

Wind it over by hand till the belt settles where it should be
Mark

I’ve been lucky, only 2 eye surgeries, one I ended up doing myself, embedded shrapnel from exploding refractory, magnet useless, swan Morton scalpel to de skin it, ophthalmology was a fail but I...

You only got a creepy joe problem because he fixed up she gee pong when he visited Obama, they gave all their intel to put him in charge! (Coo in China, adverse political opponents etc)
Mark

From whit I see on the tv the zombies all live a happy fulfilled life in Washington, they come after you by post
Mark

Did you put baffles in?, perforated plates,
Mark

Don’t panic, the scale on my saw is crap also, I use a protractor, but these digital angle things like a little box are supposed to be good, my problem is even more bizarre, fixed blade no tilt and...

Rub with white soap bar, heat till it blackens the old fashioned way!
Mark
Sorry limy,and others poor reading skills must be the CoViD

Looked a bit like a stone splitter I recently saw
Mark

It would be near impossible to run any kind of Lance off an acetylene generator, not enough flow really from my experience, plus handling carbide etc
It may, ..may be possible with arcair, I mean it...