Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Peter from Holland

Page 1 of 60 1 2 3 4

Search: Search took 0.06 seconds.

  1. [QUOTE=Trueturning;3603428]The assumption might...

    [QUOTE=Trueturning;3603428]The assumption might be that having 14 parties would work better because that is how it is done in your home? There are coalitions within our parties. Outside looking in I...
  2. A bit of OT but it came up here I always...

    A bit of OT but it came up here
    I always wondered why there is such a rancour between democrats and republicans in the US
    Perhaps it is because in the US you have only 2 dominant parties
    So...
  3. Replies
    10
    Views
    2,364

    There are hundreds of manuals available on that...

    There are hundreds of manuals available on that site BTW

    For the 12S too...
  4. Replies
    10
    Views
    2,364

    Manual for the 14 is also available on that site...

    Manual for the 14 is also available on that site I mentione earlier
    Here are 2 direkt links to them...
  5. I know but the nice part if you make them...

    I know but the nice part if you make them yourself is that you can turn them to size so it runs true then

    Peter
  6. This old post of mine is of use perhaps to make...

    This old post of mine is of use perhaps to make your own mandrel
  7. Replies
    10
    Views
    2,364

    Plenty of manuals available on that French forum...

    Plenty of manuals available on that French forum mentioned in the sticky in the 'machinery manuals&brochures' section here on PM
    You have to log in to download any manuals now (opportunity to...
  8. How many did you count and what percentage is...

    How many did you count and what percentage is that ??? Peanuts IMHO
    Very easy to skip a thread
    Its not that it is that you have to read all posts
    About paying
    If there has to be some paying...
  9. Replies
    24
    Views
    1,141

    Only price perhaps Also for getting it programmed...

    Only price perhaps Also for getting it programmed

    Peter
  10. Replies
    24
    Views
    1,141

    I was thinking the same Even though many are...

    I was thinking the same
    Even though many are 4/5 axis

    Peter
  11. I imagened the frequency of breating was...

    I imagened the frequency of breating was simultanisly with the movement of the table
    Isn`t that the case ??
    For some reason I thought to remember the hum was only at the end of stroke But I mix...
  12. the breating of the hose makes it run smooth...

    the breating of the hose makes it run smooth again
    That is the accumulating effect So that has to be kept

    Peter
  13. So J&S went cheap A hose dubbling as a...

    So J&S went cheap
    A hose dubbling as a accumulator :D


    Peter
  14. If the ID is smaller as on the original hoses the...

    If the ID is smaller as on the original hoses the speed of the oil gets higher That can cause the hum
    Pressure is pretty low so wallthicknes can be smaller as on standard hose So while the OD can...
  15. I prefer a scraped surface for blueing Never saw...

    I prefer a scraped surface for blueing Never saw scraped granite plate so I use CI
    Peter
  16. Replies
    51
    Views
    1,524

    VDF s have a wide range of input voltage these...

    VDF s have a wide range of input voltage these days
    I heard it being done here about 12 years ago already That is 240 volt motor on 400 volt net and going constant torque up to 400 volts 86 Hz
    ...
  17. Replies
    9
    Views
    1,034

    Oke I bite The taper should hold it It can...

    Oke I bite
    The taper should hold it
    It can only unscrew when the taper gives in
    So FWIW I don`t think it will come off

    Peter
  18. It is not uncommen to have one line of the...

    It is not uncommen to have one line of the transformer connected to ground
    If you have the machine under power but furhtermore nothing switched on and in this situation the fuse holds you can...
  19. Replies
    8
    Views
    593

    At max speed the drive should generate 165 volts...

    At max speed the drive should generate 165 volts DC But when the motor is bad the drive cannot get to that 165 volts perhaps Perhaps you can measure the drive with the motor disconnected I think...
  20. Replies
    51
    Views
    2,202

    The wearring is a kind of turcite Perhaps...

    The wearring is a kind of turcite
    Perhaps trapped air is the problem
    Peter
  21. Replies
    8
    Views
    593

    Before making to much costs remember that a new...

    Before making to much costs remember that a new drive is only about 600 euro from the OEM
    They can also repare the old one for about half that cost Prices are ex shippingcost from Germany
    To test...
  22. Are the hoses the original size?? Perhaps...

    Are the hoses the original size??
    Perhaps replaced in its lifetime with one with a smaller ID
    Had a bad noise once on a hydraulic system which was fixed with a bigger hose

    Peter
  23. Replies
    31
    Views
    1,914

    Last one I made was with my last employer But...

    Last one I made was with my last employer But for the turntable a possibility is to mill 2 slots in the side of a rougly 20x100mm of aluminium so that it can slide in the middle T slot The COG I...
  24. I have seen injection moulds placed on them They...

    I have seen injection moulds placed on them They had 1" plywood on top and no casters I bet that mould was more as 750 kg
    Peter
  25. Replies
    31
    Views
    1,914

    I never would drill a hole for a lifting eye The...

    I never would drill a hole for a lifting eye The idea is that I make a lifting device .rigid if possible, that has a single lifting eye big enough for the crane hook to pass in a position that it...
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4