Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: awander

Page 1 of 38 1 2 3 4

Search: Search took 0.01 seconds.

  1. Are you cutting toward or away from the...

    Are you cutting toward or away from the tailstock?

    What is the length of the taper? What diameter do you end at?
  2. Replies
    27
    Views
    1,758

    The color of the line really has nothing to do...

    The color of the line really has nothing to do with whether it is a zener diode or not.

    Most glass-cased diodes will have a black line(though I have seen some with a white line).

    Most...
  3. Replies
    25
    Views
    1,764

    You have the cutting bit the wrong way round in...

    You have the cutting bit the wrong way round in that photo-the cutting edge should be on the side of the slot that is close to center line of the round tool shank.
  4. Replies
    75
    Views
    13,870

    Why do you guys care that people are replying to...

    Why do you guys care that people are replying to a 4 year old thread? Has the world changed enough in those 4 years that the thread is no longer relevant?
  5. Replies
    28
    Views
    2,620

    The stuff I've used is 0.0625", or approximately...

    The stuff I've used is 0.0625", or approximately 1.58mm, and it bends just fine without cracking. I've bent it to 135" or even more without any problem.
  6. Replies
    8
    Views
    8,568

    Better late than never...

    Better late than never...
  7. Replies
    73
    Views
    7,176

    C'mon, Gordon, lots of folks would say you come...

    C'mon, Gordon, lots of folks would say you come across that way as well.....and I'd still buy from you...
  8. Replies
    33
    Views
    2,465

    How do you figure? Almost 1/2 of the bottom is...

    How do you figure? Almost 1/2 of the bottom is not visible in comstockfriend's photos.



    Where do you see a set screw?
  9. That's what I would say, also. If you gave us...

    That's what I would say, also.

    If you gave us a couple of the heights with the number of degrees stamped on them, we could figure out if that would work, and what length sine bar would be needed.
  10. Replies
    15
    Views
    1,628

    Brownell's sells screwdriver handles and...

    Brownell's sells screwdriver handles and interchangeable bits, including a small set of very thin ones,
    BROWNELLS MAGNA-TIP(R) THIN-BIT SET | Brownells
  11. I'm a tinkerer as well, but the thing that would...

    I'm a tinkerer as well, but the thing that would make me hesitate to build one of these is how to seal the electrical stuff away from the coolant.
  12. Replies
    20
    Views
    8,741

    it's a lot harder to make a symmetrical triangle...

    it's a lot harder to make a symmetrical triangle than it is a round shank.
  13. Replies
    12
    Views
    1,442

    Yeah, impact sockets are generally a soft...

    Yeah, impact sockets are generally a soft steel(so it doesn't break under the impacts). You won't know if you can weld it until you try.
  14. Replies
    8
    Views
    776

    I like Laser Cutting and Sheet Metal Fabrication...

    I like Laser Cutting and Sheet Metal Fabrication – Philadelphia Area – McMahon Welding, Inc. dba

    I know the owner.
  15. Replies
    15
    Views
    983

    If you can use brass: Lamp Parts - Lighting...

    If you can use brass:

    Lamp Parts - Lighting Parts - Chandelier Parts | 1/2in. Diameter Ball - 8/32 Threaded Brass Ball - Polished Nickel Finish | BB0-1/2X8/32NP | Grand Brass Lamp Parts, LLC.
  16. Welcome to the fold, as it were! Looks like you...

    Welcome to the fold, as it were! Looks like you got a decent haul there.

    Did you get any of the other rods for the 443 Depth Mic?
  17. Replies
    40
    Views
    2,433

    Bill: I have a couple of boxes full of old...

    Bill:

    I have a couple of boxes full of old switch, relay, and contactor parts. Post a picture of what you need and I'll see if I have anything that would work for you.
  18. Replies
    26
    Views
    2,015

    I never knew that. If they are indicating...

    I never knew that.

    If they are indicating coordinates, and not just distances, shouldn't the numbers then be negative?
  19. Replies
    26
    Views
    2,015

    How do you get that?

    How do you get that?
  20. Replies
    26
    Views
    2,015

    He asked for the position of the center point...

    He asked for the position of the center point between the 2 holes, and almost all of the comments are talking about pythagoras and angles, etc....

    Why use trigonometry at all?

    Simply add 12 in...
  21. Replies
    14
    Views
    1,148

    You really need to post at least a sketch, so we...

    You really need to post at least a sketch, so we can have a better idea of what you're trying to do.
  22. Replies
    30
    Views
    2,666

    It's not a waste of time if they can reuse the...

    It's not a waste of time if they can reuse the material easily.
  23. Replies
    30
    Views
    2,666

    Why do all machining videos need to include the...

    Why do all machining videos need to include the irritating music?

    Would it be so bad if we heard (...gasp!...) the machines?
  24. Replies
    28
    Views
    2,620

    I've done a lot of work with 3003H14. It bends...

    I've done a lot of work with 3003H14. It bends and punches nicely. It is a little gummy when milling.
  25. What do you mean?

    What do you mean?
Results 1 to 25 of 931
Page 1 of 38 1 2 3 4