Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: D Nelson

Page 1 of 43 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    10
    Views
    543

    https://uploads.tapatalk-cdn.com/20200128/b4cfb46c...

    https://uploads.tapatalk-cdn.com/20200128/b4cfb46c9d8238ad14a6b88010d0f35a.jpg here is the proper code at tool change and end of program to keep it from over traveling the tool change height
    Don
    ...
  2. Replies
    10
    Views
    543

    Are you using a cam system to program with? ...

    Are you using a cam system to program with?


    Sent from my iPhone using Tapatalk Pro
  3. Replies
    10
    Views
    543

    If you put a value in the z fixture for E2 it...

    If you put a value in the z fixture for E2 it will over run the tool change height. If you exceed the height of a tool the z will over travel and fault out
    Don


    Sent from my iPhone using...
  4. Replies
    54
    Views
    2,716

    Drive it to Florida You can take me too ...

    Drive it to Florida
    You can take me too


    Sent from my iPhone using Tapatalk Pro
  5. I like it also how many moneys Don Sent...

    I like it also how many moneys
    Don


    Sent from my iPhone using Tapatalk Pro
  6. Replies
    52
    Views
    3,821

    Thatís the way he was for me also and 17.00 for...

    Thatís the way he was for me also and 17.00 for Er 16. 25 or 32 cheap enough I put drills ,taps anything that isnít turning 15 k in them so far Iím happy. Now every drill is in a holder ready to go...
  7. Replies
    7
    Views
    347

    It has to come up to clear the tools to rotate to...

    It has to come up to clear the tools to rotate to the next tool
    Don


    Sent from my iPhone using Tapatalk Pro
  8. Replies
    7
    Views
    347

    Why would you mess with the limit? Sent from...

    Why would you mess with the limit?


    Sent from my iPhone using Tapatalk Pro
  9. Just run it you will never know. Don Sent...

    Just run it you will never know.
    Don


    Sent from my iPhone using Tapatalk Pro
  10. Yeah just unbolt it the doors kind of ride on it...

    Yeah just unbolt it the doors kind of ride on it but it will be fine clean it up and reseal it


    Sent from my iPhone using Tapatalk Pro
  11. Take the front panel off clean it off and put new...

    Take the front panel off clean it off and put new sealer on it
    Don


    Sent from my iPhone using Tapatalk Pro
  12. Replies
    52
    Views
    3,821

    If it doesnít measure up to your expectations...

    If it doesnít measure up to your expectations send it back. I donít understand wondering about the quality check it and send them back if they donít blow your skirt up
    Don


    Sent from my iPhone...
  13. Replies
    52
    Views
    3,821

    You can buy er16 25 32 for 17.00 each from CME...

    You can buy er16 25 32 for 17.00 each from CME tools Michigan they work fine no problems here collets 5 bucks each draw bars 4 bucks each
    Don


    Sent from my iPhone using Tapatalk Pro
  14. Replies
    45
    Views
    2,593

    No problem glad it helped you out let me know if...

    No problem glad it helped you out let me know if you need anything else
    Don


    Sent from my iPhone using Tapatalk Pro
  15. Replies
    31
    Views
    3,247

    Small riser and...

    Small riser and visehttps://uploads.tapatalk-cdn.com/20200102/aa2597194dea3128ef0d943f9de739fa.jpg


    Sent from my iPhone using Tapatalk Pro
  16. Replies
    31
    Views
    3,247

    Riser block for new...

    Riser block for new viseshttps://uploads.tapatalk-cdn.com/20200102/bcbaef85d88beed6b813b54509e4e40f.jpg


    Sent from my iPhone using Tapatalk Pro
  17. Replies
    45
    Views
    2,593

    All tools set off table. I use a heimer I zero it...

    All tools set off table. I use a heimer I zero it off the table using H 36 tool offset. Then from mdi type H36 cycle start stop it when it starts to move down in z hit jog that keeps you in the right...
  18. Replies
    45
    Views
    2,593

    Here is one with a tool change...

    Here is one with a tool change https://uploads.tapatalk-cdn.com/20200102/cde6d33c7e5d40bf54d316a4b4c9854a.jpg


    Sent from my iPhone using Tapatalk Pro
  19. Replies
    45
    Views
    2,593

    Here is a program...

    Here is a program https://uploads.tapatalk-cdn.com/20200102/27a73f2cc9f92b2735a039b31c12a577.jpg


    Sent from my iPhone using Tapatalk Pro
  20. Replies
    45
    Views
    2,593

    Itís common in a fadal if you put anything in the...

    Itís common in a fadal if you put anything in the fixture of set it will over travel the z at a tool change you have to use proper codes to overcome it
    Don


    Sent from my iPhone using Tapatalk...
  21. Replies
    31
    Views
    3,247

    The holidays got me screwed and the weekend. If...

    The holidays got me screwed and the weekend. If I adjust setting 179 I think it sets the size of the part for the rotary that helps the swarf tool paths it was set to 10 inches I set it to 1 inch...
  22. Replies
    31
    Views
    3,247

    The same reason here Sent from my iPhone...

    The same reason here


    Sent from my iPhone using Tapatalk Pro
  23. Replies
    31
    Views
    3,247

    We are just starting some test cuts on a new...

    We are just starting some test cuts on a new umc1000 ss we are having troubles with simultaneous 5 axis cuts the c axis is slow as hell we are using a post from postability it isnít using inverse...
  24. Replies
    15
    Views
    906

    There is a mark on the right side of the z column...

    There is a mark on the right side of the z column up high you must line them up before you cold start the machine also the x and y axis also need to be lined up first or the tool change height wonít...
  25. Replies
    35
    Views
    3,192

    They will be here tomorrow to set up machine I...

    They will be here tomorrow to set up machine I will get to the bottom and report back we bought simulation from mastercam for the umc1000 including the sheet metal so trying to figure it alll out...
Results 1 to 25 of 1052
Page 1 of 43 1 2 3 4