Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: jz814

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    2
    Views
    386

    Ive had this issue in the past. One time my...

    Ive had this issue in the past. One time my compact cylinder that controls the open and closing of the upper guide went bad and had to replace it. The other times i've had this issue was using a...
  2. Replies
    4
    Views
    395

    I have a LP33W control on my sodick. Same as...

    I have a LP33W control on my sodick. Same as Mike1974 posted, uses the M02 at the end of the program and stays there until you hit the home button on your control, and that will take you back to the...
  3. Replies
    18
    Views
    1,725

    Are you dropping any slugs off of the part? It...

    Are you dropping any slugs off of the part? It doesn't take much movement to loose .0005 tolerance on concentricity. Maybe switch your program around so you could stop and double check your zero...
  4. Replies
    3
    Views
    695

    What kind of machine are you running? There are...

    What kind of machine are you running? There are alot of variables that can contribute to the wear. I typically do 1 rough and 3 skims and move my power contacts about every 150 hrs.
  5. Replies
    7
    Views
    1,004

    nlancaster Hey forget the indicating of the...

    nlancaster
    Hey forget the indicating of the alignment block and just use a square when you put the block on the table or just align to the part it self. Do you align the U and V once a day? Or do...
  6. Replies
    10
    Views
    1,478

    I've had luck using the U/V alignment in hole...

    I've had luck using the U/V alignment in hole with a decent finish in it. Go for it.
  7. Replies
    9
    Views
    1,228

    I would be hesitant relying solely on a magnetic...

    I would be hesitant relying solely on a magnetic v-block to hold your part. Magnets work good but you won't have much surface area to mag too. Depending on how much stock you have to hold onto and...
  8. This won't really help save much time, but if...

    This won't really help save much time, but if your upper head is low enough, M36 is tank door half way and M46 is up all the way.
  9. I've never talked to Sodick about a code or...

    I've never talked to Sodick about a code or setting but if you are at your machine while this is running, you can hit the HALT button after the T91, hit THREAD and start again and it will skip the...
  10. Replies
    25
    Views
    2,764

    How many employees do you have programing? We...

    How many employees do you have programing? We have 15 guys that do all their own programing (no production work), one or two computers doesn't work for us. Each guy has a computer on their desk where...
  11. Hey Shane030173, Having some issues with my...

    Hey Shane030173,
    Having some issues with my wire getting programs when I post them. Its working right now, but sometimes it acts like it doesn't refresh the SEIKAnet and I have to do a couple...
  12. Replies
    10
    Views
    1,478

    nlancaster, Hey I also run a Sodick and use 3R...

    nlancaster,
    Hey I also run a Sodick and use 3R bases with custom fixture quite often. If you have the centering fixture for your 3R, you should be able to put that on and square your wire to that...
  13. Hey thanks for the idea. These calipers were...

    Hey thanks for the idea. These calipers were specific to the customers request but after doing some research they were rated to be submerged in up to 3ft of water for a max of 30min. I was able to...
  14. Replies
    3
    Views
    782

    I don't have that machine software combo but I do...

    I don't have that machine software combo but I do use mastercam for all my programming. I run a Sodick, and for 4axis work when my bottom geometry is above my work table, I place "0" at the bottom of...
  15. Replies
    5
    Views
    790

    I cut some Inconel not to long ago, about 4in or...

    I cut some Inconel not to long ago, about 4in or so thick. I treated it like regular steel and just checked for taper before I made the finish pass.
  16. Thread: Sodick AG600L

    by jz814
    Replies
    2
    Views
    628

    I do not have a LN2W control, but try going to...

    I do not have a LN2W control, but try going to Settings and going to your User 2 page. I have a LP33w control, but i do not know if they are similar or not. Hope that helps ya
  17. Hey just curious if you were able to resolve your...

    Hey just curious if you were able to resolve your issue?
  18. Check your conductivity pieces too, they might...

    Check your conductivity pieces too, they might need cleaned and moved. Also if your AWT cut bin is full, I've seen in some cases where pieces of wire can get hung up in the threader.
  19. Hey they are IP67. Thanks again

    Hey they are IP67. Thanks again
  20. I thought about that, but they are for a customer...

    I thought about that, but they are for a customer and I don't want to risk damaging any type if seal or adhesive that might be there.
  21. Hey thanks for that info, I did see some numbers...

    Hey thanks for that info, I did see some numbers on them, but I’ll have to check tomorrow.
  22. Coolant Proof Calipers need profile cut on Wire EDM

    I have an odd job on a pair of Mitutoyo Digital Coolant Proof calipers. I need to wire a form in the jaws but I am not sure if I should submerge these while I cut them or if I should just go with un...
  23. I finished my parts today with the .006 wire....

    I finished my parts today with the .006 wire. Went pretty good, had to make a couple condition adjustments because the wire kept breaking at first, but I got tweaked in.
  24. Yeah I like my standard .010 wire. We are looking...

    Yeah I like my standard .010 wire. We are looking at a new VL600Q and someone suggested switching our standard wire size down and I really hope they don't.
  25. Awesome, I found my notes and I have WT at 70 and...

    Awesome, I found my notes and I have WT at 70 and WK at .015. Thanks for the response
Results 1 to 25 of 40
Page 1 of 2 1 2