Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: cpifer3

Page 1 of 10 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    77
    Views
    22,584

    Its called a cam pro and it is pretty much...

    Its called a cam pro and it is pretty much exactly what Perry described. Encoder on the end of the cam and dial indicator with correct size roller. Enter all your parameters (rocker ratio, tappet...
  2. Replies
    25
    Views
    1,583

    PM sent in regards to PT-380

    PM sent in regards to PT-380
  3. Id be interested in some of the ring and thread...

    Id be interested in some of the ring and thread gauges depending on size?
  4. Download fixture offsets from meldas 60 control

    Anybody know how to download fixture offsets (G54,G55 etc) from a Mitsubishi Meldas 60 control via rs-232?? I can download tool offsets, but I cant figure out how to get the fixture offsets...
  5. Replies
    21
    Views
    1,894

    That is slick! Can you elaborate on how you did...

    That is slick! Can you elaborate on how you did it?
  6. Replies
    13
    Views
    897

    If you pry between the flange and the tool...

    If you pry between the flange and the tool holder, does the tool holder move?? Just wandering if your belleville washers are shot and your loosing clamping force on the tool holder?
  7. Replies
    21
    Views
    1,894

    Do you have a small vmc? Could make a fixture to...

    Do you have a small vmc? Could make a fixture to clamp them vertical, run 6 or more at a time. Depends on tolerance etc
  8. Replies
    44
    Views
    5,050

    Got the same email about the price increase.

    Got the same email about the price increase.
  9. Replies
    77
    Views
    22,584

    Never thought of trying it that way. Would...

    Never thought of trying it that way. Would probably work good depending on the profile of the cam.
  10. Replies
    77
    Views
    22,584

    yep, 8620 3/8 ball mill, cam profile wrapped...

    yep, 8620
    3/8 ball mill, cam profile wrapped around the A axis, so the Z and the A move in sync to create the lobe, .01 to .02 step over in X. Worst part was diggin through the machine parameters to...
  11. Replies
    77
    Views
    22,584

    First time using the steady rest on the mill. Had...

    First time using the steady rest on the mill. Had to rough out some cams before going out to HT and grind. I know its a cobbled up set up, but I only had 5 parts to do.
  12. Replies
    77
    Views
    22,584

    4340 heat treated to about 40rc, blanks are are...

    4340 heat treated to about 40rc, blanks are are heat treated and then machined. Tried it the other way around and had parts come back from heat treat with what appeared to be de lamination, or...
  13. Replies
    77
    Views
    22,584

    Made up a fixture using some Mitee Bites, still...

    Made up a fixture using some Mitee Bites, still early in the game but they seem to be working pretty good. Need to do some tweeking to make loading and un-loading a little better.
  14. I have a 2004 GLS-200M, Same as Rod Man, C axis...

    I have a 2004 GLS-200M, Same as Rod Man, C axis no Y. I bought it used about 6 years ago I think. Ive had pretty good luck with it, repeats very well. Little shy on spindle torque for steel parts...
  15. Replies
    0
    Views
    756

    Iscar multi master 6 flute heads

    I bought these in a lot of tooling, and have more than I need. I thought they were brand new 12mm, but when I got home and measured them, they are all about .002 thou shy, so I assume they are re...
  16. Replies
    4
    Views
    505

    The power company was not to bad, but then a...

    The power company was not to bad, but then a license contractor has to go from the pole to the building,CT panel(if over 400 amps),and into your new panel, breakers etc. The contractor and all the...
  17. Replies
    4
    Views
    505

    advice on Phase perfect option

    Long story short, I need to move into a building I bought. It has a 200 amp 208 volt 3 phase service. One of my machines is a 50 taper MITS hmc that books at 84 kva. So there goes that service. I put...
  18. Replies
    52
    Views
    3,764

    12L machines about as easy as it gets, may be...

    12L machines about as easy as it gets, may be nice for small feature parts
  19. Ive had good luck with Garr VRX , and gorilla...

    Ive had good luck with Garr VRX , and gorilla mill (CGC Tool i think) 1/2 - 1 1/4 loc in everything from 4140 to 1018, but Im not doing enough volume to truly say its better than brand a or b....
  20. Replies
    12
    Views
    777

    Id talk to some of your tool reps, some times...

    Id talk to some of your tool reps, some times they can do a little better on package deals than what you see online or in the book. At least that was my experience.
    I like short projection collet...
  21. Replies
    29
    Views
    1,866

    I agree, but the other 8X drills I had quoted...

    I agree, but the other 8X drills I had quoted all required a pilot hole (guess that should of been my red flag),so now were talking two drills,two tips etc.. Which ,yes, in the end I will end up...
  22. Replies
    29
    Views
    1,866

    Checked run at tip on new drill body sumitomo...

    Checked run at tip on new drill body sumitomo sent (this is the one I used yesterday) , just at .001 at tip. Clearance between holder and body is .0003-.00045 best I can measure. I will try TG100...
  23. Replies
    29
    Views
    1,866

    Yes, same machine, same set up. I believe it was...

    Yes, same machine, same set up. I believe it was 1018 CR though , instead of 1020
  24. Replies
    29
    Views
    1,866

    Well job is done, and I got my ass kicked! Never...

    Well job is done, and I got my ass kicked! Never got the holes to straighten out. Last time I did these I used some cobalt tipped Allied spade drills I had, gen2 I believe. Could not break a chip...
  25. Replies
    29
    Views
    1,866

    yep, faced true on both entry and exit. I just...

    yep, faced true on both entry and exit. I just tried drilling from both sides (via rotate B180.), drilled half way, and got a pretty good discrepancy at the intersection point on one hole, but not to...
Results 1 to 25 of 246
Page 1 of 10 1 2 3 4