Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: JJM

Search: Search took 0.00 seconds.

  1. John is right, we had manual with diagram as...

    John is right, we had manual with diagram as well, this is from older control, not sure if it applies to you, but "most likely / test carefully" and B it is.

    260963
  2. Replies
    64
    Views
    5,053

    There was a note listed under inch versions that...

    There was a note listed under inch versions that they are available for order 1/3 2018. So i guess they are somewhat new, and are being added. Guess i should ask from our sandvik representative,...
  3. Replies
    64
    Views
    5,053

    Thought i saw these somewhere, only few to choose...

    Thought i saw these somewhere, only few to choose from though. Only listed on silent tools catalog, not on their turning tools catalog.

    HT06-SL32D-172, HT06-SL40D-208 & HT06-SL50D-268-40R.
    ...
  4. Replies
    64
    Views
    5,053

    150mm seems to be right, (H1 480 - E4 175), 305mm...

    150mm seems to be right, (H1 480 - E4 175), 305mm for part+tool assembly in radial direction. At least 75-100mm for holder.

    SMW quick change chucks are most common what we have here, more options...
  5. Replies
    64
    Views
    5,053

    The tool name vs number can be a matter of...

    The tool name vs number can be a matter of preference and much about work enviroment as well. There is no right or wrong here. Prefer a name because it's easier to remember.

    Regardless of machine...
  6. Replies
    11
    Views
    1,891

    I think most if not all insert drill...

    I think most if not all insert drill manufacturers usually list the offset value per drill body on their book/site/catalog. At least sandvik and tungaloy had.

    It is different for each body, and...
  7. Replies
    64
    Views
    5,053

    We have few different types of CTX Beta 1250:s on...

    We have few different types of CTX Beta 1250:s on the floor.

    One that is branded Graziano was our first one, bought used. with hsk63 taper and subspindle. Without going into too much detail, it's...
  8. Thread: Cnc newbie help

    by JJM
    Replies
    5
    Views
    798

    Unlike fanuc, siemens manuals are free to...

    Unlike fanuc, siemens manuals are free to download and read, problem is that there are a mountain of those, and they have thousands of pages.

    But as for starters i would suggest "Programming...
  9. Haven't used fgref personally. If your spindle...

    Haven't used fgref personally. If your spindle number is 1 where you are holding your part during engraving, then yes. I'm not familiar with emco machines, so i don't know how it numbers its spindles.
  10. Depends on the axis of machine, since some...

    Depends on the axis of machine, since some machines can have c1-c4, and x1,x2,z1,z2, use the axis of your machine.

    fgroup (c,z,x)

    (page 355)...
  11. If i understood correctly, not sure if works on...

    If i understood correctly, not sure if works on 828D, but you might be looking for fgroup.

    fgroup(c3,x1,z1) for example.
  12. Replies
    2
    Views
    1,394

    Tool monitoring system incorporated with the...

    Tool monitoring system incorporated with the control is most likely the easiest way to do it. You can monitor either with minutes cut or number of parts, after it reaches the specified amount it...
  13. Deflection issue due to cutting depth, very low...

    Deflection issue due to cutting depth, very low cutting speed etc. Up to 32mm, asked sandvik rep if they could make one for special about week ago, no reply sofar (Holiday season).

    As for...
  14. Looking for internal carbide boring bar manufacturers (pref interchangable heads)

    Hello,

    Short question, im looking for rigid internal carbide boring bars such as Sandvik SL system. ->

    57-2C 32 218

    Combined with "neutral" heads

    57-DDXNR-32-11
Results 1 to 14 of 14