Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Mark Rand

Page 1 of 60 1 2 3 4

Search: Search took 0.05 seconds.

  1. Replies
    27
    Views
    1,895

    It isn't normally a problem. The steel sections...

    It isn't normally a problem. The steel sections seem to clean the wheel as the brass loads it. It's better if you grind with coolant. But the modern 'brass' chucks are far better than the older...
  2. Your lad's already got resurected once on PM! :D

    Your lad's already got resurected once on PM! :D
  3. Thread: Recession?

    by Mark Rand
    Replies
    2,663
    Views
    138,861

    Rolls Royce are planning up to 8,000 job cuts....

    Rolls Royce are planning up to 8,000 job cuts. Mostly in the UK.
    Maclaran (tiny in comparison) are planning 1,200. The only good news is that they can't do it while folks are on furlough, I think...
  4. Replies
    28
    Views
    19,537

    Ordered on the 24th. Arrived today, the 27th in...

    Ordered on the 24th. Arrived today, the 27th in England. Can't complain about the speed. :D
  5. Replies
    133
    Views
    5,917

    No useful advice and no knowledge of the system...

    No useful advice and no knowledge of the system except what you good people are posting but... Would it be better to have one single Federal tax system (with charges/rebates to states as appropriate)...
  6. Bugger all the party political he said-she said...

    Bugger all the party political he said-she said stuff:-

    What ideas have folks got towards getting back to work while minimising the risks of getting or passing on the infection? Working in a...
  7. Unemployment had been falling for six years under...

    Unemployment had been falling for six years under President Obama, after the fiancial crisis that he inherited came to an end. President Trump inherited that trend...


    Darn, need to refresh the...
  8. Replies
    28
    Views
    19,537

    Darn it! That just cost me $9 for the books and...

    Darn it! That just cost me $9 for the books and $27 for the postage. :crazy:
  9. I use two pins set into pieces of angle iron,...

    I use two pins set into pieces of angle iron, welded onto the inside of my lathe cabinet cupboard. A little bit of clearance on the pins is all that's needed, given that the tool holders are fairly...
  10. Replies
    17
    Views
    1,096

    It appears to be a pressure gauge secondary...

    It appears to be a pressure gauge secondary calibration set. The test gauge is fittet to one of the pipe ends and the gauge under test is fitted to the other. The pump plunger is screwed in to raise...
  11. The vial you got will be .0002"/10" or...

    The vial you got will be .0002"/10" or .00024"/foot
  12. I was under the impression, from what I read in...

    I was under the impression, from what I read in the past, that Bronze is a poor bearing material compared with cast iron for causing wear in cases where the screw is not hardened or the lubrication...
  13. Some of it may well be that the online companies...

    Some of it may well be that the online companies are facing an enormous increase in traffic to all their departments because of the bricks-and-mortar businessed being on hold. They still have to...
  14. Thread: Recession?

    by Mark Rand
    Replies
    2,663
    Views
    138,861

    Just so long as you've also got at least 5lb of...

    Just so long as you've also got at least 5lb of chillis and about 50lb of grindable beef to go with the beans and rice. With those, the beans and rice are just about edible. :D
  15. Replies
    6
    Views
    532

    Should be 20% VAT, since it's in the UK. 6%...

    Should be 20% VAT, since it's in the UK. 6% commission seems to be on the low side for the auction houses.
  16. Nah, just cough on him. :D

    Nah, just cough on him. :D
  17. Stupid bitch would complain that the year 2000...

    Stupid bitch would complain that the year 2000 problem was a hoax because people spent years making sure that banks, businesses and governments didn't go tits up because of the things that were being...
  18. Replies
    6
    Views
    532

    Barry Jordan had a bit of a speciality in...

    Barry Jordan had a bit of a speciality in building models of machine tools. All in 1/5 scale.
  19. Replies
    25
    Views
    1,677

    You say changing the SFM didn't make much of a...

    You say changing the SFM didn't make much of a difference. What was the SFM?

    Also, what is your infeed?
  20. Nital being 2% (some folks use 5%) nitric acid...

    Nital being 2% (some folks use 5%) nitric acid dissolved in denatured alcohol.
  21. Replies
    13
    Views
    904

    Going back to the lapping, rather than the...

    Going back to the lapping, rather than the measuring:- Did you clean the coarser diamond grit off the lapp before applying the finer grit? and if so, how?

    Regards
    Mark
  22. Umm... Putty as a balance weight is perfectly ok...

    Umm...
    Putty as a balance weight is perfectly ok in a small rotor, so long as it's a quick setting styrene/epoxy/whatever type. Not very well integrated with a production line, automated two plane...
  23. Might have deleted their account and booked onto...

    Might have deleted their account and booked onto a course of lessons at the Monarchist/Thermite school of English as she is spoken in a Hong Kong/New England accent. :D
  24. I'm feeling embarrassed that the only thing...

    I'm feeling embarrassed that the only thing upsetting me was that I'd been boring an aluminium part up to a saddle stop and the swarf was packing around the tip and the boring bar as the diameter...
  25. Replies
    23
    Views
    1,616

    HLV or HLV-H? what age is it? what condition are...

    HLV or HLV-H? what age is it? what condition are the parts in?
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4